lkml.org 
[lkml]   [2019]   [May]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/2] mfd: rk808: Prepare rk805 for poweroff
Date
RK805 has SLEEP signal, which can put the device into SLEEP or OFF
mode. The default is SLEEP mode.

However, when the kernel performs power-off (actually the ATF) the
device will not go fully off and this will result in higher power
consumption and inability to wake the device with RTC alarm.

The solution is to enable pm_power_off_prepare function, which will
configure SLEEP pin for OFF function.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
---
Changes for v2:
- Move pm_pwroff_prep_fn to header
- Check pm_power_off_prepare before make it NULL

drivers/mfd/rk808.c | 29 +++++++++++++++++++++++++++++
include/linux/mfd/rk808.h | 1 +
2 files changed, 30 insertions(+)

diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index c0b179792bbf..fb6cdf900899 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -387,6 +387,24 @@ static void rk805_device_shutdown(void)
dev_err(&rk808_i2c_client->dev, "power off error!\n");
}

+static void rk805_device_shutdown_prepare(void)
+{
+ int ret;
+ struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
+
+ if (!rk808) {
+ dev_warn(&rk808_i2c_client->dev,
+ "have no rk805, so do nothing here\n");
+ return;
+ }
+
+ ret = regmap_update_bits(rk808->regmap,
+ RK805_GPIO_IO_POL_REG,
+ SLP_SD_MSK, SHUTDOWN_FUN);
+ if (ret)
+ dev_err(&rk808_i2c_client->dev, "power off error!\n");
+}
+
static void rk808_device_shutdown(void)
{
int ret;
@@ -475,6 +493,7 @@ static int rk808_probe(struct i2c_client *client,
cells = rk805s;
nr_cells = ARRAY_SIZE(rk805s);
rk808->pm_pwroff_fn = rk805_device_shutdown;
+ rk808->pm_pwroff_prep_fn = rk805_device_shutdown_prepare;
break;
case RK808_ID:
rk808->regmap_cfg = &rk808_regmap_config;
@@ -550,6 +569,12 @@ static int rk808_probe(struct i2c_client *client,
pm_power_off = rk808->pm_pwroff_fn;
}

+ if (pm_off && !pm_power_off_prepare) {
+ if (!rk808_i2c_client)
+ rk808_i2c_client = client;
+ pm_power_off_prepare = rk808->pm_pwroff_prep_fn;
+ }
+
return 0;

err_irq:
@@ -566,6 +591,10 @@ static int rk808_remove(struct i2c_client *client)
if (rk808->pm_pwroff_fn && pm_power_off == rk808->pm_pwroff_fn)
pm_power_off = NULL;

+ if (rk808->pm_pwroff_prep_fn &&
+ pm_power_off_prepare == rk808->pm_pwroff_prep_fn)
+ pm_power_off_prepare = NULL;
+
return 0;
}

diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index 8b5d68a7bb9c..ec928173e507 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -454,5 +454,6 @@ struct rk808 {
const struct regmap_config *regmap_cfg;
const struct regmap_irq_chip *regmap_irq_chip;
void (*pm_pwroff_fn)(void);
+ void (*pm_pwroff_prep_fn)(void);
};
#endif /* __LINUX_REGULATOR_RK808_H */
--
2.17.1
\
 
 \ /
  Last update: 2019-05-21 08:36    [W:0.116 / U:8.844 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site