lkml.org 
[lkml]   [2019]   [May]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 2/5] arm64: dts: meson: g12a: add ethernet pinctrl definitions
Date
Jerome Brunet <jbrunet@baylibre.com> writes:

> On Sat, 2019-05-11 at 19:06 +0200, Martin Blumenstingl wrote:
>> Hi Jerome,
>>
>> On Fri, May 10, 2019 at 6:49 PM Jerome Brunet <jbrunet@baylibre.com> wrote:
>> > Add the ethernet pinctrl settings for RMII, RGMII and internal phy leds
>> >
>> > Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
>> > ---
>> > arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 37 +++++++++++++++++++++
>> > 1 file changed, 37 insertions(+)
>> >
>> > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
>> > index a32db09809f7..fe0f73730525 100644
>> > --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
>> > +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
>> > @@ -206,6 +206,43 @@
>> > };
>> > };
>> >
>> > + eth_leds_pins: eth-leds {
>> > + mux {
>> > + groups = "eth_link_led",
>> > + "eth_act_led";
>> > + function = "eth";
>> > + bias-disable;
>> > + };
>> > + };
>> > +
>> > + eth_rmii_pins: eth-rmii {
>> > + mux {
>> > + groups = "eth_mdio",
>> > + "eth_mdc",
>> > + "eth_rgmii_rx_clk",
>> > + "eth_rx_dv",
>> > + "eth_rxd0",
>> > + "eth_rxd1",
>> > + "eth_txen",
>> > + "eth_txd0",
>> > + "eth_txd1";
>> > + function = "eth";
>> > + bias-disable;
>> > + };
>> > + };
>> > +
>> > + eth_rgmii_pins: eth-rgmii {
>> > + mux {
>> > + groups = "eth_rxd2_rgmii",
>> > + "eth_rxd3_rgmii",
>> > + "eth_rgmii_tx_clk",
>> > + "eth_txd2_rgmii",
>> > + "eth_txd3_rgmii";
>> > + function = "eth";
>> > + bias-disable;
>> > + };
>> > + };
>> it seems that the group definition is incomplete (missing things like
>> eth_mdc, eth_rx_dv, ...)
>>
>> we could also mix the eth_rmii_pins and eth_rgmii_pins in a board.dts
>> (maybe that was your idea in the first place?):
>
> yes that's the idea
>
>> phy-mode = "rgmii";
>> pinctrl-0 = <&eth_rmii_pins>, <&eth_rgmii_pins>;
>> pinctrl-names = "default";
>> however, in this case I would prefer if "eth_rmii_pins" was named only
>> "eth_pins" (following mostly what Amlogic does with the pin group
>> naming: eth_* for pins that are valid in both, rmii and rgmii mode and
>> eth*rgmii* for pins that are only valid in rgmii mode)
>
> I can't say I share your preference. I let Kevin decide what he wants.
>
It seems we've gone the eth_pins route for meson-gxl.dtsi, so I'd prefer
to be consistent with that.

Kevin

\
 
 \ /
  Last update: 2019-05-15 02:11    [W:0.049 / U:16.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site