lkml.org 
[lkml]   [2019]   [Apr]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 13/13] [DO NOT MERGE] arm64: dts: allwinner: orange-pi-3: Enable WiFi
Date
From: Ondrej Jirman <megous@megous.com>

Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).

WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.

You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:

https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256

Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:

brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt

Signed-off-by: Ondrej Jirman <megous@megous.com>
---
.../dts/allwinner/sun50i-h6-orangepi-3.dts | 48 +++++++++++++++++++
1 file changed, 48 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
index f5595653b2c5..37efcca58a30 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
@@ -66,6 +66,26 @@
regulator-always-on;
};

+ reg_vcc33_wifi: vcc33-wifi {
+ /* Always on 3.3V regulator for WiFi and BT */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc33-wifi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&reg_vcc5v>;
+ };
+
+ reg_vcc_wifi_io: vcc-wifi-io {
+ /* Always on 1.8V/300mA regulator for WiFi and BT IO */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-wifi-io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ vin-supply = <&reg_vcc33_wifi>;
+ };
+
/*
* The board uses 2.5V RGMII signalling. Power sequence to enable
* the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2) power rails
@@ -86,6 +106,14 @@
*/
vin-supply = <&reg_aldo2>; /* GMAC-3V3 */
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+ post-power-on-delay-ms = <200>;
+ };
};

&cpu0 {
@@ -146,6 +174,25 @@
status = "okay";
};

+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&reg_vcc33_wifi>;
+ vqmmc-supply = <&reg_vcc_wifi_io>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcm: sdio-wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
+ interrupt-names = "host-wake";
+ };
+};
+
&ohci0 {
status = "okay";
};
@@ -157,6 +204,7 @@
&pio {
vcc-pc-supply = <&reg_bldo2>;
vcc-pd-supply = <&reg_cldo1>;
+ vcc-pg-supply = <&reg_vcc_wifi_io>;
};

&r_i2c {
--
2.21.0
\
 
 \ /
  Last update: 2019-04-09 02:27    [W:0.142 / U:0.376 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site