lkml.org 
[lkml]   [2019]   [Apr]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v5 2/8] i2c: iproc: Add slave mode support
Hi Ray/Wolfram,

On Tue, Apr 2, 2019 at 3:03 AM Ray Jui <ray.jui@broadcom.com> wrote:
>
> Hi Wolfram/Rayagonda,
>
> On 3/27/2019 3:14 PM, Wolfram Sang wrote:
> >
> >> +static void bcm_iproc_i2c_slave_init(
> >> + struct bcm_iproc_i2c_dev *iproc_i2c, bool need_reset)
> >> +{
> >> + u32 val;
> >> +
> >> + if (need_reset) {
> >> + /* put controller in reset */
> >> + val = readl(iproc_i2c->base + CFG_OFFSET);
> >> + val |= BIT(CFG_RESET_SHIFT);
> >> + writel(val, iproc_i2c->base + CFG_OFFSET);
> >> +
> >> + /* wait 100 usec per spec */
> >> + udelay(100);
> >> +
> >> + /* bring controller out of reset */
> >> + val &= ~(BIT(CFG_RESET_SHIFT));
> >> + writel(val, iproc_i2c->base + CFG_OFFSET);
> >> + }
> >> +
> >> + /* flush TX/RX FIFOs */
> >> + val = (BIT(S_FIFO_RX_FLUSH_SHIFT) | BIT(S_FIFO_TX_FLUSH_SHIFT));
> >> + writel(val, iproc_i2c->base + S_FIFO_CTRL_OFFSET);
> >
> > Will flushing FIFOs work when a slave is register while a master
> > transfer is on-going at the same time?
> >
>
> Okay, as you pointed out in a subsequent email, this can't happen.
>
> >> +
> >> + /* RANDOM SLAVE STRETCH time - 20ms*/
> >
> > What is a "random stretch time"? 20ms sounds like a lot. Also, missing
> > space before comment terminator.
> >
>
> Rayagonda,
>
> Could you please help to comment on the choice of the 20 ms to allow
> clock stretch from the slave? In probably all cases, the slave should
> not need more than 1 ms? 20 ms does seem way too long as Wolfram pointed
> out.

In fact we are programming max slave stretch time ie 25ms, comment
should be correcting.
Its maximum time for slave to complete read/write operation, if slave
is done with read/write then clock will not be stretched further, it
will be released immediately.
Hence I feel no harm in programming max timeout value.
Also determining correct slave stretch is very subjective and depends
on slave type as well.

Best regards,
Rayagonda

>
> Will fix the missing space before comment terminator.
>
> >> @@ -224,22 +473,25 @@ static int bcm_iproc_i2c_init(struct bcm_iproc_i2c_dev *iproc_i2c)
> >>
> >> /* put controller in reset */
> >> val = readl(iproc_i2c->base + CFG_OFFSET);
> >> - val |= 1 << CFG_RESET_SHIFT;
> >> - val &= ~(1 << CFG_EN_SHIFT);
> >> + val |= BIT(CFG_RESET_SHIFT);
> >> + val &= ~(BIT(CFG_EN_SHIFT));
> >> writel(val, iproc_i2c->base + CFG_OFFSET);
> >>
> >> /* wait 100 usec per spec */
> >> udelay(100);
> >>
> >> /* bring controller out of reset */
> >> - val &= ~(1 << CFG_RESET_SHIFT);
> >> + val &= ~(BIT(CFG_RESET_SHIFT));
> >> writel(val, iproc_i2c->base + CFG_OFFSET);
> >>
> >> /* flush TX/RX FIFOs and set RX FIFO threshold to zero */
> >> - val = (1 << M_FIFO_RX_FLUSH_SHIFT) | (1 << M_FIFO_TX_FLUSH_SHIFT);
> >> + val = (BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT));
> >> writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
> >> /* disable all interrupts */
> >> - writel(0, iproc_i2c->base + IE_OFFSET);
> >> + val = readl(iproc_i2c->base + IE_OFFSET);
> >> + val &= ~(IE_M_ALL_INTERRUPT_MASK <<
> >> + IE_M_ALL_INTERRUPT_SHIFT);
> >> + writel(val, iproc_i2c->base + IE_OFFSET);
> >
> > This block looks unrelated, but I won't be too strict here...
> >
> >> + case M_CMD_STATUS_FIFO_UNDERRUN:
> >> + dev_dbg(iproc_i2c->device, "FIFO under-run\n");
> >> + return -ENXIO;
> >> +
> >> + case M_CMD_STATUS_RX_FIFO_FULL:
> >> + dev_dbg(iproc_i2c->device, "Master Rx FIFO full > 10ms\n");
> >> + return -ETIMEDOUT;
> >> +
> >
> > ... however, this looks really unrelated to me. This is about master
> > transmission, or?
>
> This should be submitted in a separate commit. Will do that in the next
> iteration of patch series.
>
> >
> > Rest looks OK.
> >
>
> Thanks,
>
> Ray

\
 
 \ /
  Last update: 2019-04-02 10:26    [W:0.063 / U:0.596 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site