lkml.org 
[lkml]   [2019]   [Mar]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC PATCH nand-next 0/2] meson-nand: support for older SoCs
From
Date
Hi Martin,

On 2019/3/7 21:09, Miquel Raynal wrote:
> Hello,
>
> Martin Blumenstingl <martin.blumenstingl@googlemail.com> wrote on Tue,
> 5 Mar 2019 23:12:51 +0100:
>
>> Hi Liang,
>>
>> On Mon, Mar 4, 2019 at 5:55 AM Liang Yang <liang.yang@amlogic.com> wrote:
>>>
>>> Hello Martin,
>>>
>>> On 2019/3/2 2:29, Martin Blumenstingl wrote:
>>>> Hi Liang,
>>>>
>>>> I am trying to add support for older SoCs to the meson-nand driver.
>>>> Back when the driver was in development I used an early revision (of
>>>> your driver) and did some modifications to make it work on older SoCs.
>>>>
>>>> Now that the driver is upstream I wanted to give it another try and
>>>> make a real patch out of it. Unfortunately it's not working anymore.
>>>>
>>>> As far as I know the NFC IP block revision on GXL is similar (or even
>>>> the same?) as on all older SoCs. As far as I can tell only the clock
>>>> setup is different on the older SoCs (which have a dedicated NAND
>>>> clock):
>>>> - we don't need the "amlogic,mmc-syscon" property on the older SoCs
>>>> because we don't need to setup any muxing (common clock framework
>>>> will do everything for us)
>>>> - "rx" and "tx" clocks don't exist
>>>> - I could not find any other differences between Meson8, Meson8b,
>>>> Meson8m2, GXBB and GXL
>>>>
>>> That is right. the serials NFC is almost the same except:
>>> 1) The clock control and source that M8-serials are not share with EMMC.
>>> 2) The base register address
>>> 3) DMA encryption option which we don't care on NFC driver.
>> great, thank you for confirming this!
>>
>>>> In this series I'm sending two patches which add support for the older
>>>> SoCs.
>>>>
>>>> Unfortunately these patches are currently not working for me (hence the
>>>> "RFC" prefix). I get a (strange) crash which is triggered by the
>>>> kzalloc() in meson_nfc_read_buf() - see below for more details.
>>>>
>>>> Can you please help me on this one? I'd like to know whether:
>>>> - the meson-nand driver works for you on GXL or AXG on linux-next?
>>>> (I was running these patches on top of next-20190301 on my M8S
>>>> board which uses a 32-bit Meson8m2 SoC. I don't have any board using
>>>> a GXL SoC which also has NAND)
>>> Yes, it works on AXG platform using a MXIC slc nand flash(MX30LF4G); but
>>> i an not sure it runs the same flow with yours. because i see the print
>>> "Counld not find a valid ONFI parameter page, ...." in yours. i will try
>>> to reproduce it on AXG(i don't have a M8 platform now).
>> I'm looking forward to hear about the test results on your AXG boards
>> for reference: my board has a SK Hynix H27UCG8T2B (ID bytes: 0xad 0xde
>> 0x94 0xeb 0x74 0x44, 20nm MLC)
>> I have another board (where I haven't tested the NFC driver yet) with
>> a SK Hynix H27UCG8T2E (ID bytes: 0xad 0xde 0x14 0xa7 0x42 0x4a, 1Ynm
>> MLC). if it helps with your analysis I can test on that board as well
>
> Liang, you just have to fake the output of the ONFI page detection and
> you will probably run into this error which will then be easy to
> reproduce.
>

I have tested it on AXG platform; I find MX30LF4G also enter this flow ,
but it doesn't crash. log as follow:
[ 1.018056] Could not find a valid ONFI parameter page, trying
bit-wise majority to recover it
[ 1.021057] ONFI parameter recovery failed, aborting
[ 1.025966] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xdc
[ 1.032237] nand: Macronix NAND 512MiB 3,3V 8-bit
[ 1.036889] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048,
OOB size: 64
[ 1.045741] Bad block table not found for chip 0
[ 1.050077] Bad block table not found for chip 0
[ 1.053538] Scanning device for bad blocks
[ 1.069094] Bad eraseblock 20 at 0x000000280000
[ 1.071074] Bad eraseblock 24 at 0x000000300000
[ 1.127494] random: fast init done
[ 1.348754] Bad eraseblock 519 at 0x0000040e0000
[ 1.632819] Bad eraseblock 1028 at 0x000008080000
[ 2.405420] Bad eraseblock 2411 at 0x000012d60000
[ 3.349276] Bad block table written to 0x00001ffe0000, version 0x01
[ 3.350967] Bad block table written to 0x00001ffc0000, version 0x01
[ 3.356429] 5 fixed-partitions partitions found on MTD device
ffe07800.nfc
[ 3.362925] Creating 5 MTD partitions on "ffe07800.nfc":
[ 3.368188] 0x000000000000-0x000000200000 : "boot"
[ 3.373970] 0x000000200000-0x000000600000 : "env"
[ 3.378564] 0x000000600000-0x000001000000 : "system"
[ 3.383511] 0x000001000000-0x000004000000 : "rootfs"
[ 3.388525] 0x000004000000-0x00000c000000 : "media"

I am looking forward to a Hynix nand flash to test on GXL platform, and
there should be something different from MXIC flash on ONFI page
detection. I will update the result asap net week.
Do you have another type of nand flash to test on M8 platform ?
>
> Thanks,
> Miquèl
>
> .
>

\
 
 \ /
  Last update: 2019-03-07 14:36    [W:0.076 / U:0.784 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site