lkml.org 
[lkml]   [2019]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V1 07/11] mmc: cqhci: add quirk for setting DCMD CMD_TIMING
From
Date

On 3/6/2019 6:30 PM, Adrian Hunter wrote:
> On 2/03/19 7:20 AM, Sowjanya Komatineni wrote:
>> This patch adds a quirk for setting CMD_TIMING to 1 in descriptor
>> for DCMD with R1B response type to allow the command to be sent to
>> device during data activity or busy time.
>>
>> Tegra186 CQHCI host has bug where it selects DATA_PRESENT_SELECT
>> to 1 by CQHCI controller for DCMDs with R1B response type and
>> since DCMD does not trigger any data transfer, DCMD task complete
>> happens leaving the DATA FSM of host controller in wait state for
>> data.
>>
>> This effects the data transfer task issued after R1B DCMD task
>> and no interrupt is generated for the data transfer task.
>>
>> SW WAR for this issue is to set CMD_TIMING bit to 1 in DCMD task
>> descriptor and as DCMD task descriptor preparation is done by
>> cqhci driver, this patch adds cqequirk to handle this.
>>
>> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
>> ---
>> drivers/mmc/host/cqhci.c | 5 ++++-
>> drivers/mmc/host/cqhci.h | 1 +
>> 2 files changed, 5 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/mmc/host/cqhci.c b/drivers/mmc/host/cqhci.c
>> index a8af682a9182..b34c07125f32 100644
>> --- a/drivers/mmc/host/cqhci.c
>> +++ b/drivers/mmc/host/cqhci.c
>> @@ -521,7 +521,10 @@ static void cqhci_prep_dcmd_desc(struct mmc_host *mmc,
>> } else {
>> if (mrq->cmd->flags & MMC_RSP_R1B) {
>> resp_type = 0x3;
>> - timing = 0x0;
>> + if (cq_host->quirks & CQHCI_QUIRK_CMD_TIMING_R1B_DCMD)
>> + timing = 0x1;
>> + else
>> + timing = 0x0;
> I was thinking it would be nice if there was a generic way for drivers to
> make changes to descriptors before a task is started. Currently there is
> host->ops->write_l() which would make it possible by checking for CQHCI_TDBR
> register and, in this case, the DCMD tag. We would need to export
> get_desc(), perhaps rename it cqhci_get_desc() and put it in cqhci.h since
> it is an inline function.

We take spin_lock_irqsave after the descriptor is prepared and before
writing to TDBR.
Not sure but tomorrow this may become a limitation for drivers to make
changes to
descriptors if they edit descriptors in host->ops->write_l() call.
Though in this case it is not required here.

>
> Alternatively we could add host->ops for descriptor preparation.

Both ways sounds good to me.
But maybe adding a host->ops for descriptor preparation is better way to go,
since that will be the right interface exposed to make changes to
descriptors.

>
> What do people think?
>
>> } else {
>> resp_type = 0x2;
>> timing = 0x1;
>> diff --git a/drivers/mmc/host/cqhci.h b/drivers/mmc/host/cqhci.h
>> index 9e68286a07b4..f96d8565cc07 100644
>> --- a/drivers/mmc/host/cqhci.h
>> +++ b/drivers/mmc/host/cqhci.h
>> @@ -170,6 +170,7 @@ struct cqhci_host {
>>
>> u32 quirks;
>> #define CQHCI_QUIRK_SHORT_TXFR_DESC_SZ 0x1
>> +#define CQHCI_QUIRK_CMD_TIMING_R1B_DCMD 0x2
>>
>> bool enabled;
>> bool halted;
>>

\
 
 \ /
  Last update: 2019-03-07 03:45    [W:0.083 / U:1.168 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site