lkml.org 
[lkml]   [2019]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue
From
Date
Hi,
On Mon, 2019-03-04 at 11:38 +0100, Neil Armstrong wrote:
> Adds support for Amlogic G12A USB Control Glue HW.
>
> The Amlogic G12A SoC Family embeds 2 USB Controllers :
> - a DWC3 IP configured as Host for USB2 and USB3
> - a DWC2 IP configured as Peripheral USB2 Only
>
> A glue connects these both controllers to 2 USB2 PHYs, and optionnally
> to an USB3+PCIE Combo PHY shared with the PCIE controller.
>
> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
> setups the on-chip OTG mode selection for this PHY.
>
> This drivers supports the on-probe setup of the OTG mode, and manually
> via a debugfs interface. The IRQ mode change detect is yet to be added
> in a future patchset, mainly due to lack of hardware to validate on.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> drivers/usb/dwc3/Kconfig | 10 +
> drivers/usb/dwc3/Makefile | 1 +
> drivers/usb/dwc3/dwc3-meson-g12a.c | 601 +++++++++++++++++++++++++++++
> 3 files changed, 612 insertions(+)
> create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
>
> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> index 1a0404fda596..21ce7368d325 100644
> --- a/drivers/usb/dwc3/Kconfig
> +++ b/drivers/usb/dwc3/Kconfig
> @@ -93,6 +93,16 @@ config USB_DWC3_KEYSTONE
> Support of USB2/3 functionality in TI Keystone2 platforms.
> Say 'Y' or 'M' here if you have one such device
>
> +config USB_DWC3_MESON_G12A
> + tristate "Amlogic Meson G12A Platforms"
> + depends on OF && COMMON_CLK
> + depends on ARCH_MESON || COMPILE_TEST
> + default USB_DWC3
> + select USB_ROLE_SWITCH
> + help
> + Support USB2/3 functionality in Amlogic G12A platforms.
> + Say 'Y' or 'M' if you have one such device.
> +
> config USB_DWC3_OF_SIMPLE
> tristate "Generic OF Simple Glue Layer"
> depends on OF && COMMON_CLK
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index 6e3ef6144e5d..ae86da0dc5bd 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
> obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
> obj-$(CONFIG_USB_DWC3_HAPS) += dwc3-haps.o
> obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
> +obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
> obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
> obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
> obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
> diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
> new file mode 100644
> index 000000000000..75942614a034
> --- /dev/null
> +++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
> @@ -0,0 +1,601 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * USB Glue for Amlogic G12A SoCs
> + *
> + * Copyright (c) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/*
> + * The USB is organized with a glue around the DWC3 Controller IP as :
> + * - Control registers for each USB2 Ports
> + * - Control registers for the USB PHY layer
> + * - SuperSpeed PHY can be enabled only if port is used
> + *
> + * TOFIX:
> + * - Add dynamic OTG switching with ID change interrupt
> + */
> +
[...]
> +
> +static int dwc3_meson_g12a_probe(struct platform_device *pdev)
> +{
> + struct dwc3_meson_g12a *priv;
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + void __iomem *base;
> + struct resource *res;
> + enum phy_mode otg_id;
> + int ret, i;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + priv->regmap = devm_regmap_init_mmio(dev, base,
> + &phy_meson_g12a_usb3_regmap_conf);
> + if (IS_ERR(priv->regmap))
> + return PTR_ERR(priv->regmap);
> +
> + priv->vbus = devm_regulator_get_optional(dev, "vbus");
> + if (IS_ERR(priv->vbus)) {
> + if (PTR_ERR(priv->vbus) == -EPROBE_DEFER)
> + return PTR_ERR(priv->vbus);
> + priv->vbus = NULL;
> + }
> +
> + priv->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(priv->clk))
> + return PTR_ERR(priv->clk);
> +
> + ret = clk_prepare_enable(priv->clk);
> + if (ret)
> + return ret;
> +
> + platform_set_drvdata(pdev, priv);
> + priv->dev = dev;
> +
> + priv->reset = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(priv->reset)) {
> + ret = PTR_ERR(priv->reset);
> + dev_err(dev, "failed to get device reset, err=%d\n", ret);
> + return ret;
> + }
> +
> + ret = reset_control_reset(priv->reset);
> + if (ret)
> + return ret;
> +
> + ret = dwc3_meson_g12a_get_phys(priv);
> + if (ret)
> + return ret;
> +
> + ret = regulator_enable(priv->vbus);
> + if (ret)
> + return ret;
> +
> + /* Get dr_mode */
> + priv->otg_mode = usb_get_dr_mode(dev);
> +
> + dwc3_meson_g12a_usb_init(priv);
> +
> + /* Set PHY Power */
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + ret = phy_power_on(priv->phys[i]);
> + if (ret)
> + goto err_phys_put;
> + }
> +
> + /* Init PHYs */
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + ret = phy_init(priv->phys[i]);
> + if (ret)
> + goto err_phys_power;
> + }
usually phy_init() first

> +
> + ret = of_platform_populate(np, NULL, NULL, dev);
> + if (ret) {
> + clk_disable_unprepare(priv->clk);
> + clk_put(priv->clk);
> +
> + goto err_phys_exit;
> + }
> +
> + /* Setup OTG mode corresponding to the ID pin */
> + if (priv->otg_mode == USB_DR_MODE_OTG) {
> + /* TOFIX Handle ID mode toggling via IRQ */
> + otg_id = dwc3_meson_g12a_get_id(priv);
> + if (otg_id != priv->otg_phy_mode) {
> + if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
> + dev_warn(dev, "Failed to switch OTG mode\n");
> + }
> + }
> +
> + /* Setup role switcher */
> + priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
> + "snps,dwc3");
> + priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
> + priv->switch_desc.allow_userspace_control = true;
> + priv->switch_desc.set = dwc3_meson_g12a_role_set;
> + priv->switch_desc.get = dwc3_meson_g12a_role_get;
to me, use a local variable for switch_desc

> +
> + priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
> + if (IS_ERR(priv->role_switch))
> + dev_warn(dev, "Unable to register Role Switch\n");
> +
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> + pm_runtime_get_sync(dev);
> +
> + return 0;
> +
> +err_phys_exit:
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_exit(priv->phys[i]);
> +
> +err_phys_power:
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_power_off(priv->phys[i]);
> +
> +err_phys_put:
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_put(priv->phys[i]);
> +
The phys are got by devm_phy_optional_get(), no need call phy_put()
> + return ret;
> +}
> +
> +static int dwc3_meson_g12a_remove(struct platform_device *pdev)
> +{
> + struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
> + struct device *dev = &pdev->dev;
> + int i;
> +
> + usb_role_switch_unregister(priv->role_switch);
> +
> + of_platform_depopulate(dev);
> +
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + phy_power_off(priv->phys[i]);
> + phy_exit(priv->phys[i]);
> + phy_put(priv->phys[i]);
ditto
> + }
> +
> + clk_disable_unprepare(priv->clk);
> + clk_put(priv->clk);
> +
> + pm_runtime_disable(dev);
> + pm_runtime_put_noidle(dev);
> + pm_runtime_set_suspended(dev);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> +
> + clk_disable(priv->clk);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> +
> + return clk_enable(priv->clk);
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> + int i;
> +
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + if (priv->phys[i])
> + phy_exit(priv->phys[i]);
> +
> + reset_control_assert(priv->reset);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> + int i, ret;
> +
> + reset_control_deassert(priv->reset);
> +
> + dwc3_meson_g12a_usb_init(priv);
> +
> + /* Init PHYs */
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + if (priv->phys[i]) {
> + ret = phy_init(priv->phys[i]);
> + if (ret)
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
> + SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
> + dwc3_meson_g12a_runtime_resume, NULL)
> +};
> +
> +static const struct of_device_id dwc3_meson_g12a_match[] = {
> + { .compatible = "amlogic,meson-g12a-usb-ctrl" },
> + { /* Sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
> +
> +static struct platform_driver dwc3_meson_g12a_driver = {
> + .probe = dwc3_meson_g12a_probe,
> + .remove = dwc3_meson_g12a_remove,
> + .driver = {
> + .name = "dwc3-meson-g12a",
> + .of_match_table = dwc3_meson_g12a_match,
> + .pm = &dwc3_meson_g12a_dev_pm_ops,
> + },
> +};
> +
> +module_platform_driver(dwc3_meson_g12a_driver);
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
> +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");


\
 
 \ /
  Last update: 2019-03-07 03:04    [W:0.203 / U:2.396 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site