lkml.org 
[lkml]   [2019]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces
Date
Remove extra spaces before colons.

Signed-off-by: Bich Hemon <bich.hemon@st.com>
---
.../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++-----------
1 file changed, 13 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
index 69240e1..7d054f1 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
@@ -1,11 +1,11 @@
* I2C controller embedded in STMicroelectronics STM32 I2C platform

-Required properties :
-- compatible : Must be one of the following
+Required properties:
+- compatible: Must be one of the following
- "st,stm32f4-i2c"
- "st,stm32f7-i2c"
-- reg : Offset and length of the register set for the device
-- interrupts : Must contain the interrupt id for I2C event and then the
+- reg: Offset and length of the register set for the device
+- interrupts: Must contain the interrupt id for I2C event and then the
interrupt id for I2C error.
- resets: Must contain the phandle to the reset controller.
- clocks: Must contain the input clock of the I2C instance.
@@ -14,25 +14,25 @@ Required properties :
- #address-cells = <1>;
- #size-cells = <0>;

-Optional properties :
-- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
+Optional properties:
+- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified,
the default 100 kHz frequency will be used.
For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
100000 and 400000.
For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
possible values are 100000, 400000 and 1000000.
-- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
+- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board
(default: 25)
-- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
+- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board
(default: 10)
I2C Timings are derived from these 2 values
-- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG
+- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG
whether Fast Mode Plus speed is selected by slave.
- 1st cell : phandle to syscfg
- 2nd cell : register offset within SYSCFG
- 3rd cell : register bitmask for FMP bit
+ 1st cell: phandle to syscfg
+ 2nd cell: register offset within SYSCFG
+ 3rd cell: register bitmask for FMP bit

-Example :
+Example:

i2c@40005400 {
compatible = "st,stm32f4-i2c";
--
1.9.1
\
 
 \ /
  Last update: 2019-03-06 16:12    [W:0.060 / U:2.568 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site