lkml.org 
[lkml]   [2019]   [Mar]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/2] dt-bindings: i2c-stm32: remove extra spaces
From
Date
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>

On 3/6/19 4:11 PM, Bich HEMON wrote:
> Remove extra spaces before colons.
>
> Signed-off-by: Bich Hemon <bich.hemon@st.com>
> ---
> .../devicetree/bindings/i2c/i2c-stm32.txt | 26 +++++++++++-----------
> 1 file changed, 13 insertions(+), 13 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
> index 69240e1..7d054f1 100644
> --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
> +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
> @@ -1,11 +1,11 @@
> * I2C controller embedded in STMicroelectronics STM32 I2C platform
>
> -Required properties :
> -- compatible : Must be one of the following
> +Required properties:
> +- compatible: Must be one of the following
> - "st,stm32f4-i2c"
> - "st,stm32f7-i2c"
> -- reg : Offset and length of the register set for the device
> -- interrupts : Must contain the interrupt id for I2C event and then the
> +- reg: Offset and length of the register set for the device
> +- interrupts: Must contain the interrupt id for I2C event and then the
> interrupt id for I2C error.
> - resets: Must contain the phandle to the reset controller.
> - clocks: Must contain the input clock of the I2C instance.
> @@ -14,25 +14,25 @@ Required properties :
> - #address-cells = <1>;
> - #size-cells = <0>;
>
> -Optional properties :
> -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
> +Optional properties:
> +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified,
> the default 100 kHz frequency will be used.
> For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
> 100000 and 400000.
> For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
> possible values are 100000, 400000 and 1000000.
> -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
> +- i2c-scl-rising-time-ns: Only for STM32F7, I2C SCL Rising time for the board
> (default: 25)
> -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
> +- i2c-scl-falling-time-ns: Only for STM32F7, I2C SCL Falling time for the board
> (default: 10)
> I2C Timings are derived from these 2 values
> -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG
> +- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG
> whether Fast Mode Plus speed is selected by slave.
> - 1st cell : phandle to syscfg
> - 2nd cell : register offset within SYSCFG
> - 3rd cell : register bitmask for FMP bit
> + 1st cell: phandle to syscfg
> + 2nd cell: register offset within SYSCFG
> + 3rd cell: register bitmask for FMP bit
>
> -Example :
> +Example:
>
> i2c@40005400 {
> compatible = "st,stm32f4-i2c";
>

\
 
 \ /
  Last update: 2019-03-21 09:28    [W:0.052 / U:1.304 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site