lkml.org 
[lkml]   [2019]   [Mar]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/8] iio: adc: stm32-dfsdm: make spi_master_freq more accurate
From
Date
On 3/10/19 11:09 AM, Jonathan Cameron wrote:
> On Wed, 6 Mar 2019 09:55:17 +0100
> Fabrice Gasnier <fabrice.gasnier@st.com> wrote:
>
>> When SPI clock isn't accurate, 'spi_master_freq' is filled in with
>> expected frequency. Use computed value instead:
>> - e.g. source clock / (CKOUTDIV + 1)
>> Also, current divider may be set to value that makes CKOUT to exceed
>> spi-max-frequency. Rather use lower value (e.g. round up divider when
>> ckout isn't accurate).
>>
>> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
>> ---
>> drivers/iio/adc/stm32-dfsdm-core.c | 9 +++++++--
>> 1 file changed, 7 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/iio/adc/stm32-dfsdm-core.c b/drivers/iio/adc/stm32-dfsdm-core.c
>> index bf089f5..65b7556 100644
>> --- a/drivers/iio/adc/stm32-dfsdm-core.c
>> +++ b/drivers/iio/adc/stm32-dfsdm-core.c
>> @@ -243,13 +243,18 @@ static int stm32_dfsdm_parse_of(struct platform_device *pdev,
>> return 0;
>> }
>>
>> - priv->spi_clk_out_div = div_u64_rem(clk_freq, spi_freq, &rem) - 1;
>> + priv->spi_clk_out_div = div_u64_rem(clk_freq, spi_freq, &rem);
>> +
>> + /* round up divider when clkout isn't accurate (e.g. !rem) */
>> + if (priv->spi_clk_out_div && !rem)
>> + priv->spi_clk_out_div--;
>> +
> This comment perhaps needs adjusting because at the moment it looks
> like it decrements when it is accurate. With the old code in place
> in the patch it's obvious that's because you actually want one less.
>
> Might even be worth the dance of
>
> /* round up if not precise */
> if (priv->spi_clk_out_div && rem)
> priv->spi_clk_out_div++;
>
> /* subtract one because.... */
> priv->spi_clk_out_div--;

Hi Jonathan,

I'll rework this patch in v2, make it easier to understand & read.

In a few words: the clock output is divider = ckoutdiv + 1.
ckoutdiv range can be from 1-255 to provide divider of 2-256.
So I'll introduce this divider as a variable, and use it to setup
spi_clk_out_div.
This should address all your remarks here.

Thanks for reviewing,
Best Regards,
Fabrice
>
>> if (!priv->spi_clk_out_div) {
>> /* spi_clk_out_div == 0 means ckout is OFF */
>> dev_err(&pdev->dev, "spi-max-frequency not achievable\n");
>> return -EINVAL;
>> }
>> - priv->dfsdm.spi_master_freq = spi_freq;
>> + priv->dfsdm.spi_master_freq = clk_freq / (priv->spi_clk_out_div + 1);
> And we increment it again here? That needs an explanation as well.
>>
>> if (rem) {
>> dev_warn(&pdev->dev, "SPI clock not accurate\n");
>

\
 
 \ /
  Last update: 2019-03-21 14:42    [W:0.045 / U:34.712 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site