lkml.org 
[lkml]   [2019]   [Mar]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [RFC 1/2] dt-bindings: imx6q-pcie: Add support for i.MX8QM/QXP PCIe
From
Date
Hi Richard,

Am Mittwoch, den 13.03.2019, 09:15 +0000 schrieb Richard Zhu:
> Add codes needed to support i.MX8QM/QXP PCIe.
> - HSIO(High Speed IO) subsystem is new defined on i.MX8QM/QXP.
>   The PCIe and SATA modules are contained in the HSIO subsystem. There
>   are two PCIe, one SATA controllers and three mixed lane PHYs on
>   i.MX8QM. There are three use cases of the HSIO subsystem on i.MX8QM.
>   1. PCIea 2 lanes and one SATA AHCI port.
>   2. PCIea 1 lane, PCIeb 1 lane and one SATA AHCI port.
>   3. PCIea 2 lanes, PCIeb 1 lane.
>   i.MX8QXP only has PCIeb controller and one lane PHY.
>   Use the hsio-cfg property to specify the different modes.
> - The HSIO address map as viewed from system level is as shown below.
>   address [31:24]    Local address    Target    Address Size
>   5F                 0                HSIO      16MB
>   60-6F              40-4F            HSIO      256MB
>   70-7F              80-8F            HSIO      256MB
>   The property local-addr is required to specify it.
> - Both external OSC and internal PLL can be used as PCIe reference
>   clock, use the ext_osc property to distinguish them.
> - clock request GPIO for controlling the PCI reference clock request
>   signal. And should be configure OD when L1SS maybe enabled later.
> - One more power domain HSIO_GPIO and clock PCIE_PER are required by
>   i.MX8QM/QXP PCIe.
>   Add these specific properties to enable i.MX8QM/QXP PCIe.

All this HSIO handling should move into a separate PHY driver. This has
nothing to do with the PCIe controller itself. See for example the
Tegra XUSB PHY driver (drivers/phy/tegra/xusb.c), which is a similar
combined PCIE/USB3/SATA PHY driver.

Regards,
Lucas

> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
> ---
>  .../devicetree/bindings/pci/fsl,imx6q-pcie.txt      | 21 +++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> index a7f5f5a..f7586c9 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> @@ -10,6 +10,8 @@ Required properties:
> >   - "fsl,imx6qp-pcie"
> >   - "fsl,imx7d-pcie"
> >   - "fsl,imx8mq-pcie"
> > + - "fsl,imx8qm-pcie"
> > + - "fsl,imx8qxp-pcie"
>  - reg: base address and length of the PCIe controller
>  - interrupts: A list of interrupt outputs of the controller. Must contain an
>    entry for each entry in the interrupt-names property.
> @@ -38,6 +40,10 @@ Optional properties:
>    The regulator will be enabled when initializing the PCIe host and
>    disabled either as part of the init process or when shutting down the
>    host.
> +- clkreq-gpio: Should specify the GPIO for controlling the PCI reference clock
> +  request signal.
> +- ext_osc: External OSC is used as PCIe reference clock or not. 0: Internal
> +  PLL. 1: External OSC.
>  
>  Additional required properties for imx6sx-pcie:
>  - clock names: Must include the following additional entries:
> @@ -60,6 +66,21 @@ Additional required properties for imx8mq-pcie:
>  - clock-names: Must include the following additional entries:
> >   - "pcie_aux"
>  
> +Additional required properties for imx8qm/qxp pcie:
> +- power-domains: Must be set to a phandle pointing to PCIE, PCIE_PHY power and
> +  HSIO_GPIO domains
> +- power-domain-names: Must be "pcie", "pcie_phy", "hsio_gpio"
> +- clock-names: Must include the following additional entries:
> > + - "pcie_per"
> +- hsio-cfg: hsio configration mode when the pcie node is supported.
> +  1: pciea 2 lanes and one sata ahci port.
> +  2: pciea 1 lane, pcieb 1 lane and one sata ahci port.
> +  3: pciea 2 lanes, pcieb 1 lane.
> +- local-addr: the local address used in hsio module on i.MX8QM/QXP.
> > + Example:
> > + hsio-cfg = <2>;
> > + local-addr = <0x80000000>;
> +
>  Example:
>  
> >   pcie@01000000 {

\
 
 \ /
  Last update: 2019-03-14 10:30    [W:0.144 / U:4.424 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site