lkml.org 
[lkml]   [2019]   [Mar]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 14/14] ARM: dts: sun8i: s3l: add support for Pine64 Single Cube Computer
Date
The Single Cube Computer kit by Pine64 is a development kit with
Allwinner S3L SoC.

It comes with a main board, an expansion board and a camera.

The main board features a Micro-USB power-only jack, a USB Type-A port,
an Ethernet port connected to the internal PHY of the SoC. A RGB LED
port is reserved on the board.

The expansion board features a TF slot, a microphone and a speaker
connector with on-board amplifier.

Add support for the kit, with features on the main board and the
expansion board now.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/sun8i-s3l-single-cube-computer.dts | 166 ++++++++++++++++++
2 files changed, 167 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aeaf3298..a77d1a000953 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1096,6 +1096,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-r16-nintendo-super-nes-classic.dtb \
sun8i-r16-parrot.dtb \
sun8i-r40-bananapi-m2-ultra.dtb \
+ sun8i-s3l-single-cube-computer.dtb \
sun8i-t3-cqa3t-bv3.dtb \
sun8i-v3s-licheepi-zero.dtb \
sun8i-v3s-licheepi-zero-dock.dtb \
diff --git a/arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts b/arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts
new file mode 100644
index 000000000000..a014de597c8a
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2019 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+#include "sun8i-s3l.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Pine64 Single Cube Computer";
+ compatible = "pine64,single-cube-computer", "allwinner,sun8i-s3l";
+
+ aliases {
+ serial0 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ label = "pine64:green:led1";
+ gpios = <&pio 1 11 GPIO_ACTIVE_LOW>; /* PB11 */
+ };
+
+ led2 {
+ label = "pine64:green:led2";
+ gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
+ };
+
+ led3 {
+ label = "pine64:green:led3";
+ gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */
+ };
+
+ led4 {
+ label = "pine64:green:led4";
+ gpios = <&pio 1 13 GPIO_ACTIVE_LOW>; /* PB13 */
+ };
+ };
+
+ reg_vcc5v0: vcc5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_vcc_wifi: vcc-wifi {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-wifi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */
+ vin-supply = <&reg_dcdc3>;
+ startup-delay-us = <200000>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp203",
+ "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <&reg_dcdc3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <&reg_vcc_wifi>;
+ vqmmc-supply = <&reg_dcdc3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&pio {
+ vcc-pd-supply = <&reg_dcdc3>;
+ vcc-pe-supply = <&reg_ldo3>;
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-sys-cpu-ephy";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+&reg_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-pe";
+};
+
+&reg_ldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avdd-mipi";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus-supply = <&reg_vcc5v0>;
+ status = "okay";
+};
--
2.18.1
\
 
 \ /
  Last update: 2019-03-12 16:34    [W:0.079 / U:2.956 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site