lkml.org 
[lkml]   [2019]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] dt-bindings: display: rockchip: add document for rk3066 hdmi
On Wed, Feb 27, 2019 at 12:04 PM Johan Jonker <jbx6244@gmail.com> wrote:
>
> Thanks for your advice.
>
> On 2/25/19 5:59 PM, Rob Herring wrote:> On Fri, Feb 01, 2019 at
> 01:32:35PM +0100, Johan Jonker wrote:
> >> This patch adds a binding that describes the HDMI controller for
> >> rk3066.
> >
> > This is not using the DW block like other Rockchip SoCs (IIRC)?
>
> As outsider it's a little bit difficult to comment on that.
> Maybe an insider can give a better answer.
> The rk3066 is there early model.
> Reusing blocks like in the later improved models wasn't in the fashion
> yet I think.
> Also comparing the rk3066-hdmi driver to the inno driver gives too many
> differences in registers, sound support and irqs.
> If it was similar they would have combined it in there own kernel.
> Given the age there won't come any other support for it.
> This is what we have...

Okay, if it looks different then good enough for me.

> >> Signed-off-by: Johan Jonker <jbx6244@gmail.com>
> >> ---
> >> .../display/rockchip/rk3066_hdmi-rockchip.txt | 60
> ++++++++++++++++++++++
> >
> > Using the compatible string plus '.txt' is the preferred naming.
>
> Will change that in V2.
> rk3066-hdmi -> rk3066-hdmi-rockchip.txt
>
> How about the other documents?
> rk3036-inno-hdmi -> inno_hdmi-rockchip.txt
> rk3288-dw-hdmi -> dw_hdmi-rockchip.txt
> rk3288-dp -> analogix_dp-rockchip.txt
> etc.

Just leave them for now.

> >> 1 file changed, 60 insertions(+)
> >> create mode 100644
> Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
> >>
> >> diff --git
> a/Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
> b/Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
> >> new file mode 100644
> >> index 000000000..6a8f3754f
> >> --- /dev/null
> >> +++
> b/Documentation/devicetree/bindings/display/rockchip/rk3066_hdmi-rockchip.txt
> >> @@ -0,0 +1,60 @@
> >> +Rockchip specific extensions for rk3066 HDMI
> >> +============================================
> >> +
> >> +Required properties:
> >> +- compatible:
> >> + "rockchip,rk3066-hdmi";
> >> +- reg:
> >> + Physical base address and length of the controller's registers.
> >> +- clocks, clock-names:
> >> + Phandle to HDMI controller clock, name should be "hclk".
> >> +- interrupts:
> >> + HDMI interrupt number.
> >> +- power-domains:
> >> + Phandle to the RK3066_PD_VIO power domain.
> >> +- rockchip,grf:
> >> + This soc uses GRF regs to switch the HDMI TX input between vop0 and
> vop1.
> >> +- ports:
>
> Should "ports" be replaced by: "hdmi_in: port"?
> What is preferred?
>
> There are two different methods in use:
> -1
> hdmi_in: port {
>
> -2
> ports {
> hdmi_in: port {

Generally, you have 'ports' when there is more than one 'port' node
which you should in this case.

> >> + Contains one port node with two endpoints, numbered 0 and 1,
> >> + connected respectively to vop0 and vop1.
> >
> > You should have an output port to an hdmi-connector node (or bridge) as
> > well.
>
> Which hdmi-connector node?
> Could you explane with an example?

grep hdmi-connector in the tree there's lot's of examples.

> The Rockchip hdmi nodes I'm aware off only use the port nodes as a way
> to switch the hdmi input between the vop's.
> The vop nodes can have multiple outputs.

Yes, that's the input side. And generally, muxing is represented as
multiple endpoints.

Not all cases of HDMI have defined a connector node as that came along later.

Rob

\
 
 \ /
  Last update: 2019-02-27 20:07    [W:0.052 / U:1.756 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site