lkml.org 
[lkml]   [2019]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 2/5] x86/percpu: Relax smp_processor_id()
Nadav reported that since this_cpu_read() became asm-volatile, many
smp_processor_id() users generated worse code due to the extra
constraints.

However since smp_processor_id() is reading a stable value, we can use
__this_cpu_read().

Reported-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
---
arch/x86/include/asm/smp.h | 3 ++-
include/linux/smp.h | 45 +++++++++++++++++++++++++++++++--------------
2 files changed, 33 insertions(+), 15 deletions(-)

--- a/arch/x86/include/asm/smp.h
+++ b/arch/x86/include/asm/smp.h
@@ -162,7 +162,8 @@ __visible void smp_call_function_single_
* from the initial startup. We map APIC_BASE very early in page_setup(),
* so this is correct in the x86 case.
*/
-#define raw_smp_processor_id() (this_cpu_read(cpu_number))
+#define raw_smp_processor_id() this_cpu_read(cpu_number)
+#define __smp_processor_id() __this_cpu_read(cpu_number)

#ifdef CONFIG_X86_32
extern int safe_smp_processor_id(void);
--- a/include/linux/smp.h
+++ b/include/linux/smp.h
@@ -181,29 +181,46 @@ static inline int get_boot_cpu_id(void)

#endif /* !SMP */

-/*
- * smp_processor_id(): get the current CPU ID.
+/**
+ * raw_processor_id() - get the current (unstable) CPU id
+ *
+ * For then you know what you are doing and need an unstable
+ * CPU id.
+ */
+
+/**
+ * smp_processor_id() - get the current (stable) CPU id
+ *
+ * This is the normal accessor to the CPU id and should be used
+ * whenever possible.
*
- * if DEBUG_PREEMPT is enabled then we check whether it is
- * used in a preemption-safe way. (smp_processor_id() is safe
- * if it's used in a preemption-off critical section, or in
- * a thread that is bound to the current CPU.)
+ * The CPU id is stable when:
+ *
+ * - IRQs are disabled;
+ * - preemption is disabled;
+ * - the task is CPU affine.
*
- * NOTE: raw_smp_processor_id() is for internal use only
- * (smp_processor_id() is the preferred variant), but in rare
- * instances it might also be used to turn off false positives
- * (i.e. smp_processor_id() use that the debugging code reports but
- * which use for some reason is legal). Don't use this to hack around
- * the warning message, as your code might not work under PREEMPT.
+ * When CONFIG_DEBUG_PREEMPT; we verify these assumption and WARN
+ * when smp_processor_id() is used when the CPU id is not stable.
*/
+
+/*
+ * Allow the architecture to differentiate between a stable and unstable read.
+ * For example, x86 uses an IRQ-safe asm-volatile read for the unstable but a
+ * regular asm read for the stable.
+ */
+#ifndef __smp_processor_id
+#define __smp_processor_id(x) raw_smp_processor_id(x)
+#endif
+
#ifdef CONFIG_DEBUG_PREEMPT
extern unsigned int debug_smp_processor_id(void);
# define smp_processor_id() debug_smp_processor_id()
#else
-# define smp_processor_id() raw_smp_processor_id()
+# define smp_processor_id() __smp_processor_id()
#endif

-#define get_cpu() ({ preempt_disable(); smp_processor_id(); })
+#define get_cpu() ({ preempt_disable(); __smp_processor_id(); })
#define put_cpu() preempt_enable()

/*

\
 
 \ /
  Last update: 2019-02-27 11:17    [W:0.077 / U:6.412 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site