lkml.org 
[lkml]   [2019]   [Feb]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v5 08/13] x86/fsgsbase/64: Introduce the FIND_PERCPU_BASE macro
On Fri, Feb 1, 2019 at 12:55 PM Chang S. Bae <chang.seok.bae@intel.com> wrote:
>
> GSBASE is used to find per-CPU data in the kernel. But when it is unknown,
> the per-CPU base can be found from the per_cpu_offset table with a CPU NR.
> The CPU NR is extracted from the limit field of the CPUNODE entry in GDT,
> or by the RDPID instruction.
>
> Also, add the GAS-compatible RDPID macro.
>
> The new macro will be used on a following patch.
>
> Suggested-by: H. Peter Anvin <hpa@zytor.com>
> Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
> Cc: Andy Lutomirski <luto@kernel.org>
> Cc: Thomas Gleixner <tglx@linutronix.de>
> Cc: Ingo Molnar <mingo@kernel.org>
> Cc: Dave Hansen <dave.hansen@linux.intel.com>
> Cc: Andi Kleen <ak@linux.intel.com>
> ---
> arch/x86/include/asm/fsgsbase.h | 46 +++++++++++++++++++++++++++++++++
> arch/x86/include/asm/inst.h | 15 +++++++++++
> 2 files changed, 61 insertions(+)
>
> diff --git a/arch/x86/include/asm/fsgsbase.h b/arch/x86/include/asm/fsgsbase.h
> index aefd53767a5d..eecca2250748 100644
> --- a/arch/x86/include/asm/fsgsbase.h
> +++ b/arch/x86/include/asm/fsgsbase.h
> @@ -78,6 +78,52 @@ extern void x86_gsbase_write_cpu_inactive(unsigned long gsbase);
>
> #endif /* CONFIG_X86_64 */
>
> +#else /* __ASSEMBLY__ */
> +
> +#ifdef CONFIG_X86_64
> +
> +#include <asm/inst.h>
> +
> +#if CONFIG_SMP

ifdef?

> +
> +/*
> + * CPU/node NR is loaded from the limit (size) field of a special segment
> + * descriptor entry in GDT.
> + */
> +.macro LOAD_CPU_AND_NODE_SEG_LIMIT reg:req
> + movq $__CPUNODE_SEG, \reg
> + lsl \reg, \reg
> +.endm
> +

Please put the alternative in here instead of in FIND_PERCPU_BASE.

> +/*
> + * Fetch the per-CPU GSBASE value for this processor and put it in @reg.
> + * We normally use %gs for accessing per-CPU data, but we are setting up
> + * %gs here and obviously can not use %gs itself to access per-CPU data.
> + */
> +.macro FIND_PERCPU_BASE reg:req
> + /*
> + * The CPU/node NR is initialized earlier, directly in cpu_init().
> + * The CPU NR is extracted from it.
> + */

This comment is unnecessary.

> + ALTERNATIVE \
> + "LOAD_CPU_AND_NODE_SEG_LIMIT \reg", \
> + "RDPID \reg", \
> + X86_FEATURE_RDPID
> + andq $VDSO_CPUNODE_MASK, \reg
> + movq __per_cpu_offset(, \reg, 8), \reg
> +.endm
> +
> +#else
> +
> +.macro FIND_PERCPU_BASE reg:req
> + /* Tracking the base offset value */

I don't understand this comment at all. Please just remove it.

\
 
 \ /
  Last update: 2019-02-02 18:18    [W:0.152 / U:10.740 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site