lkml.org 
[lkml]   [2019]   [Feb]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/8] dt-bindings: leds: Add binding for axp20x-led device driver
Date
This adds the devicetree bindings for charge led indicator found
on most of X-Powers AXP20X PMICs.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
---
.../devicetree/bindings/leds/leds-axp20x.txt | 74 +++++++++++++++++++
1 file changed, 74 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/leds-axp20x.txt

diff --git a/Documentation/devicetree/bindings/leds/leds-axp20x.txt b/Documentation/devicetree/bindings/leds/leds-axp20x.txt
new file mode 100644
index 000000000000..5a83ad06796d
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-axp20x.txt
@@ -0,0 +1,74 @@
+Device Tree Bindings for LED support on X-Powers PMIC
+
+Most of the X-Powers PMICs have integrated battery charger with LED indicator.
+The output is open-drain, so the state is either high-Z or output-low. The
+driver is a subnode of AXP20X MFD driver, since it uses shared bus with all
+other cells.
+The LED can be controlled either manually or automatically. Then in automatic
+(controlled by the charger) there are two indication modes:
+
+Mode-A
+======
+- output-low: Charging
+- high-Z Not charging
+- 1Hz flashing: Abnormal alarm
+- 4Hz flashing Overvoltage alarm
+
+Mode-B
+======
+- output-low: Battery full
+- high-Z Not charging
+- 1Hz flashing: Charging
+- 4Hz flashing Overvoltage or abnormal alarm
+
+The control and the mode can be changed from sysfs.
+
+For AXP20X MFD bindings see:
+Documentation/devicetree/bindings/mfd/axp20x.txt
+
+Required properties:
+- compatible : Must be "x-powers,axp20x-led"
+
+Supported common LED properties, see ./common.txt for more informationn
+- label : See Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger : See Documentation/devicetree/bindings/leds/common.txt
+- default-state: See Documentation/devicetree/bindings/leds/common.txt
+
+Optional properties:
+- x-powers,charger-mode: 0 for Mode-A, 1 for Mode-B
+ If omitted, then the control is set to manual mode.
+ On invalid value, Mode-A is used.
+
+
+Example:
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+
+ ...
+
+ led@0 {
+ compatible = "x-powers,axp20x-led";
+ status = "okay";
+
+ label = "axp20x:yellow:chgled";
+ linux,default-trigger = "timer";
+ default-state = "on";
+ };
+ };
+
+or
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+
+ ...
+
+ led@0 {
+ compatible = "x-powers,axp20x-led";
+ status = "okay";
+
+ label = "axp20x:yellow:chgled";
+ x-powers,charger-mode = <1>;
+ };
+ };
--
2.17.1
\
 
 \ /
  Last update: 2019-02-15 12:53    [W:0.090 / U:0.724 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site