lkml.org 
[lkml]   [2019]   [Feb]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.20 07/50] iio: adc: axp288: Fix TS-pin handling
Date
4.20-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Hans de Goede <hdegoede@redhat.com>

commit 9bcf15f75cac3c6a00d8f8083a635de9c8537799 upstream.

Prior to this commit there were 3 issues with our handling of the TS-pin:

1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring

Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.

This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.

The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.

2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:

ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR

This commit fixes this by using regmap_update_bits to change only the
relevant bits.

3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.

This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545
Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
drivers/iio/adc/axp288_adc.c | 76 +++++++++++++++++++++++++++++++++----------
1 file changed, 60 insertions(+), 16 deletions(-)

--- a/drivers/iio/adc/axp288_adc.c
+++ b/drivers/iio/adc/axp288_adc.c
@@ -27,9 +27,18 @@
#include <linux/iio/machine.h>
#include <linux/iio/driver.h>

-#define AXP288_ADC_EN_MASK 0xF1
-#define AXP288_ADC_TS_PIN_GPADC 0xF2
-#define AXP288_ADC_TS_PIN_ON 0xF3
+/*
+ * This mask enables all ADCs except for the battery temp-sensor (TS), that is
+ * left as-is to avoid breaking charging on devices without a temp-sensor.
+ */
+#define AXP288_ADC_EN_MASK 0xF0
+#define AXP288_ADC_TS_ENABLE 0x01
+
+#define AXP288_ADC_TS_CURRENT_ON_OFF_MASK GENMASK(1, 0)
+#define AXP288_ADC_TS_CURRENT_OFF (0 << 0)
+#define AXP288_ADC_TS_CURRENT_ON_WHEN_CHARGING (1 << 0)
+#define AXP288_ADC_TS_CURRENT_ON_ONDEMAND (2 << 0)
+#define AXP288_ADC_TS_CURRENT_ON (3 << 0)

enum axp288_adc_id {
AXP288_ADC_TS,
@@ -44,6 +53,7 @@ enum axp288_adc_id {
struct axp288_adc_info {
int irq;
struct regmap *regmap;
+ bool ts_enabled;
};

static const struct iio_chan_spec axp288_adc_channels[] = {
@@ -115,21 +125,33 @@ static int axp288_adc_read_channel(int *
return IIO_VAL_INT;
}

-static int axp288_adc_set_ts(struct regmap *regmap, unsigned int mode,
- unsigned long address)
+/*
+ * The current-source used for the battery temp-sensor (TS) is shared
+ * with the GPADC. For proper fuel-gauge and charger operation the TS
+ * current-source needs to be permanently on. But to read the GPADC we
+ * need to temporary switch the TS current-source to ondemand, so that
+ * the GPADC can use it, otherwise we will always read an all 0 value.
+ */
+static int axp288_adc_set_ts(struct axp288_adc_info *info,
+ unsigned int mode, unsigned long address)
{
int ret;

- /* channels other than GPADC do not need to switch TS pin */
+ /* No need to switch the current-source if the TS pin is disabled */
+ if (!info->ts_enabled)
+ return 0;
+
+ /* Channels other than GPADC do not need the current source */
if (address != AXP288_GP_ADC_H)
return 0;

- ret = regmap_write(regmap, AXP288_ADC_TS_PIN_CTRL, mode);
+ ret = regmap_update_bits(info->regmap, AXP288_ADC_TS_PIN_CTRL,
+ AXP288_ADC_TS_CURRENT_ON_OFF_MASK, mode);
if (ret)
return ret;

/* When switching to the GPADC pin give things some time to settle */
- if (mode == AXP288_ADC_TS_PIN_GPADC)
+ if (mode == AXP288_ADC_TS_CURRENT_ON_ONDEMAND)
usleep_range(6000, 10000);

return 0;
@@ -145,14 +167,14 @@ static int axp288_adc_read_raw(struct ii
mutex_lock(&indio_dev->mlock);
switch (mask) {
case IIO_CHAN_INFO_RAW:
- if (axp288_adc_set_ts(info->regmap, AXP288_ADC_TS_PIN_GPADC,
+ if (axp288_adc_set_ts(info, AXP288_ADC_TS_CURRENT_ON_ONDEMAND,
chan->address)) {
dev_err(&indio_dev->dev, "GPADC mode\n");
ret = -EINVAL;
break;
}
ret = axp288_adc_read_channel(val, chan->address, info->regmap);
- if (axp288_adc_set_ts(info->regmap, AXP288_ADC_TS_PIN_ON,
+ if (axp288_adc_set_ts(info, AXP288_ADC_TS_CURRENT_ON,
chan->address))
dev_err(&indio_dev->dev, "TS pin restore\n");
break;
@@ -164,13 +186,35 @@ static int axp288_adc_read_raw(struct ii
return ret;
}

-static int axp288_adc_set_state(struct regmap *regmap)
+static int axp288_adc_initialize(struct axp288_adc_info *info)
{
- /* ADC should be always enabled for internal FG to function */
- if (regmap_write(regmap, AXP288_ADC_TS_PIN_CTRL, AXP288_ADC_TS_PIN_ON))
- return -EIO;
+ int ret, adc_enable_val;
+
+ /*
+ * Determine if the TS pin is enabled and set the TS current-source
+ * accordingly.
+ */
+ ret = regmap_read(info->regmap, AXP20X_ADC_EN1, &adc_enable_val);
+ if (ret)
+ return ret;
+
+ if (adc_enable_val & AXP288_ADC_TS_ENABLE) {
+ info->ts_enabled = true;
+ ret = regmap_update_bits(info->regmap, AXP288_ADC_TS_PIN_CTRL,
+ AXP288_ADC_TS_CURRENT_ON_OFF_MASK,
+ AXP288_ADC_TS_CURRENT_ON);
+ } else {
+ info->ts_enabled = false;
+ ret = regmap_update_bits(info->regmap, AXP288_ADC_TS_PIN_CTRL,
+ AXP288_ADC_TS_CURRENT_ON_OFF_MASK,
+ AXP288_ADC_TS_CURRENT_OFF);
+ }
+ if (ret)
+ return ret;

- return regmap_write(regmap, AXP20X_ADC_EN1, AXP288_ADC_EN_MASK);
+ /* Turn on the ADC for all channels except TS, leave TS as is */
+ return regmap_update_bits(info->regmap, AXP20X_ADC_EN1,
+ AXP288_ADC_EN_MASK, AXP288_ADC_EN_MASK);
}

static const struct iio_info axp288_adc_iio_info = {
@@ -200,7 +244,7 @@ static int axp288_adc_probe(struct platf
* Set ADC to enabled state at all time, including system suspend.
* otherwise internal fuel gauge functionality may be affected.
*/
- ret = axp288_adc_set_state(axp20x->regmap);
+ ret = axp288_adc_initialize(info);
if (ret) {
dev_err(&pdev->dev, "unable to enable ADC device\n");
return ret;

\
 
 \ /
  Last update: 2019-02-13 19:50    [W:0.221 / U:7.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site