lkml.org 
[lkml]   [2019]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 1/3] ARM: dts: imx6: rdu2: Add node for UCS1002 USB charger chip
Date
Add node for UCS1002 USB charger chip connected to front panel USB and
replace "regulator-fixed" previously used to control VBUS.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
---

Changes since [v2]:

- Rebased on recent linux-next (12/05/2019)

Changes since [v1]

- Added GPIO hog configuration to put UCS1002 into correct mode
even before its driver takes over. The code for that is taken
from similar patch from Lucas, so I added his Signed-off-by as
well.

[v2] https://lore.kernel.org/lkml/20190529071843.24767-1-andrew.smirnov@gmail.com/
[v1] lore.kernel.org/r/20190522071227.31488-1-andrew.smirnov@gmail.com

arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 77 +++++++++++++++++++------
1 file changed, 59 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
index ee364215fb9d..7531f0595bd1 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@@ -60,18 +60,6 @@
regulator-always-on;
};

- reg_5p0v_user_usb: regulator-5p0v-user-usb {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_user_usb>;
- vin-supply = <&reg_5p0v_main>;
- regulator-name = "5V_USER_USB";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
- startup-delay-us = <1000>;
- };
-
reg_3p3v_pmic: regulator-3p3v-pmic {
compatible = "regulator-fixed";
vin-supply = <&reg_12p0v>;
@@ -406,6 +394,39 @@
};
};

+&gpio3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio3_hog>;
+
+ usb-emulation {
+ gpio-hog;
+ gpios = <19 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "usb-emulation";
+ };
+
+ usb-mode1 {
+ gpio-hog;
+ gpios = <20 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-mode1";
+ };
+
+ usb-pwr {
+ gpio-hog;
+ gpios = <22 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "usb-pwr-ctrl-en-n";
+ };
+
+ usb-mode2 {
+ gpio-hog;
+ gpios = <23 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-mode2";
+ };
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
@@ -675,6 +696,16 @@
status = "disabled";
};

+ reg_5p0v_user_usb: charger@32 {
+ compatible = "microchip,ucs1002";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ucs1002_pins>;
+ reg = <0x32>;
+ interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>,
+ <&gpio3 21 IRQ_TYPE_EDGE_BOTH>;
+ interrupt-names = "a_det", "alert";
+ };
+
hpa1: amp@60 {
compatible = "ti,tpa6130a2";
pinctrl-names = "default";
@@ -1019,6 +1050,15 @@
>;
};

+ pinctrl_gpio3_hog: gpio3hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
@@ -1066,12 +1106,6 @@
>;
};

- pinctrl_reg_user_usb: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x40000038
- >;
- };
-
pinctrl_rmii_phy_irq: phygrp {
fsl,pins = <
MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x40010000
@@ -1131,6 +1165,13 @@
>;
};

+ pinctrl_ucs1002_pins: ucs1002grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0
+ MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x1b0b0
+ >;
+ };
+
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x10059
--
2.21.0
\
 
 \ /
  Last update: 2019-12-09 17:51    [W:0.033 / U:0.608 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site