lkml.org 
[lkml]   [2019]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 03/15] soc: tegra: Add Tegra PMC clock registrations into PMC driver
From
Date

On 12/9/19 12:46 PM, Sowjanya Komatineni wrote:
>
> On 12/9/19 12:12 PM, Dmitry Osipenko wrote:
>> 08.12.2019 00:36, Sowjanya Komatineni пишет:
>>> On 12/7/19 11:59 AM, Sowjanya Komatineni wrote:
>>>> On 12/7/19 8:00 AM, Dmitry Osipenko wrote:
>>>>> 07.12.2019 18:53, Dmitry Osipenko пишет:
>>>>>> 07.12.2019 18:47, Dmitry Osipenko пишет:
>>>>>>> 07.12.2019 17:28, Dmitry Osipenko пишет:
>>>>>>>> 06.12.2019 05:48, Sowjanya Komatineni пишет:
>>>>>>>>> Tegra210 and prior Tegra PMC has clk_out_1, clk_out_2, clk_out_3
>>>>>>>>> with
>>>>>>>>> mux and gate for each of these clocks.
>>>>>>>>>
>>>>>>>>> Currently these PMC clocks are registered by Tegra clock driver
>>>>>>>>> using
>>>>>>>>> clk_register_mux and clk_register_gate by passing PMC base
>>>>>>>>> address
>>>>>>>>> and register offsets and PMC programming for these clocks happens
>>>>>>>>> through direct PMC access by the clock driver.
>>>>>>>>>
>>>>>>>>> With this, when PMC is in secure mode any direct PMC access
>>>>>>>>> from the
>>>>>>>>> non-secure world does not go through and these clocks will not be
>>>>>>>>> functional.
>>>>>>>>>
>>>>>>>>> This patch adds these clocks registration with PMC as a clock
>>>>>>>>> provider
>>>>>>>>> for these clocks. clk_ops callback implementations for these
>>>>>>>>> clocks
>>>>>>>>> uses tegra_pmc_readl and tegra_pmc_writel which supports PMC
>>>>>>>>> programming
>>>>>>>>> in secure mode and non-secure mode.
>>>>>>>>>
>>>>>>>>> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
>>>>>>>>> ---
>>>>>>> [snip]
>>>>>>>
>>>>>>>>> +
>>>>>>>>> +static const struct clk_ops pmc_clk_gate_ops = {
>>>>>>>>> +    .is_enabled = pmc_clk_is_enabled,
>>>>>>>>> +    .enable = pmc_clk_enable,
>>>>>>>>> +    .disable = pmc_clk_disable,
>>>>>>>>> +};
>>>>>>>> What's the benefit of separating GATE from the MUX?
>>>>>>>>
>>>>>>>> I think it could be a single clock.
>>>>>>> According to TRM:
>>>>>>>
>>>>>>> 1. GATE and MUX are separate entities.
>>>>>>>
>>>>>>> 2. GATE is the parent of MUX (see PMC's CLK_OUT paths diagram in
>>>>>>> TRM).
>>>>>>>
>>>>>>> 3. PMC doesn't gate EXTPERIPH clock but could "force-enable" it,
>>>>>>> correct?
>>> Was following existing clk-tegra-pmc as I am not sure of reason for
>>> having these clocks registered as separate mux and gate clocks.
>>>
>>> Yes, PMC clocks can be registered as single clock and can use clk_ops
>>> for set/get parent and enable/disable.
>>>
>>> enable/disable of PMC clocks is for force-enable to force the clock to
>>> run regardless of ACCEPT_REQ or INVERT_REQ.
>>>
>>>>>> 4. clk_m_div2/4 are internal PMC OSC dividers and thus these clocks
>>>>>> should belong to PMC.
>>>>> Also, it should be "osc" and not "clk_m".
>>>> I followed the same parents as it were in existing clk-tegra-pmc
>>>> driver.
>>>>
>>>> Yeah they are wrong and they should be from osc and not clk_m.
>>>>
>>>> Will fix in next version.
>>>>
Reg clk_m_div2/3, they are dividers at OSC pad and not really internal
to PMC block.

current clock driver creates clk_m_div clocks which should actually be
osc_div2/osc_div4 clocks with osc as parent.

There are no clk_m_div2 and clk_m_div4 from clk_m

Will fix this in next version.

>> Could you please describe the full EXTPERIPH clock topology and how the
>> pinmux configuration is related to it all?
>>
>> What is internal to the Tegra chip and what are the external outputs?
>>
>> Is it possible to bypass PMC on T30+ for the EXTPERIPH clocks?
>
> PMC CLK1/2/3 possible sources are OSC_DIV1, OSC_DIV2, OSC_DIV4,
> EXTPERIPH from CAR.
>
> OSC_DIV1/2/4 are with internal dividers at the OSC Pads
>
> EXTPERIPH is from CAR and it has reset and enable controls along with
> clock source selections to choose one of the PLLA_OUT0, CLK_S,
> PLLP_OUT0, CLK_M, PLLE_OUT0
>
> So, PMC CLK1/2/4 possible parents are OSC_DIV1, OSC_DIV2, OSC_DIV4,
> EXTERN.
>
>
> CLK1/2/3 also has Pinmux to route EXTPERIPH output on to these pins.
>
>
> When EXTERN output clock is selected for these PMC clocks thru
> CLKx_SRC_SEL, output clock is from driver by EXTPERIPH from CAR via
> Pinmux logic or driven as per CLKx_SRC_SEL bypassing pinmux based on
> CLKx_ACCEPT_REQ bit.
>
>
> PMC Clock control register has bit CLKx_ACCEPT_REQ
> When CLKx_ACCEPT_REQ = 0, output clock driver is from by EXTPERIPH
> through the pinmux
> When CLKx_ACCEPT_REQ = 1, output clock is based on CLKx_SRC_SEL bits
> (OSC_DIV1/2/4 and EXTPERIPH clock bypassing the pinmux)
>
> FORCE_EN bit in PMC CLock control register forces the clock to run
> regardless of this.

\
 
 \ /
  Last update: 2019-12-10 00:03    [W:0.160 / U:5.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site