lkml.org 
[lkml]   [2019]   [Dec]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 06/15] clk: tegra: Remove tegra_pmc_clk_init along with clk ids
From
Date
07.12.2019 22:35, Sowjanya Komatineni пишет:
>
> On 12/7/19 7:04 AM, Dmitry Osipenko wrote:
>> 07.12.2019 17:43, Dmitry Osipenko пишет:
>>> 07.12.2019 17:33, Dmitry Osipenko пишет:
>>>> 06.12.2019 05:48, Sowjanya Komatineni пишет:
>>>>> Current Tegra clock driver registers PMC clocks clk_out_1, clk_out_2,
>>>>> clk_out_3 and blink output in tegra_pmc_init() which does direct Tegra
>>>>> PMC access during clk_ops and these PMC register read and write access
>>>>> will not happen when PMC is in secure mode.
>>>>>
>>>>> Any direct PMC register access from non-secure world will not go
>>>>> through and all the PMC clocks and blink control are done in Tegra PMC
>>>>> driver with PMC as clock provider.
>>>>>
>>>>> This patch removes tegra_pmc_clk_init along with corresponding clk ids
>>>>> from Tegra clock driver.
>>>>>
>>>>> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
>>>>> ---
>>>> [snip]
>>>>
>>>>> @@ -1230,9 +1222,6 @@ static struct tegra_clk_init_table
>>>>> init_table[] __initdata = {
>>>>>       { TEGRA30_CLK_PLL_A, TEGRA30_CLK_CLK_MAX, 564480000, 1 },
>>>>>       { TEGRA30_CLK_PLL_A_OUT0, TEGRA30_CLK_CLK_MAX, 11289600, 1 },
>>>>>       { TEGRA30_CLK_EXTERN1, TEGRA30_CLK_PLL_A_OUT0, 0, 1 },
>>>> Perhaps these clocks do not need to be always-enabled?
>>>>
>>>> [snip]
>>>>
>>> Also, EXTERN1 parent configuration should be moved to the audio
>>> driver/device-tree as well.
>> Ah, I missed that it's done in the patch #10.
> Yes its done in Patch#10
>>
>>> Maybe it even makes sense to move the whole configuration, including
>>> PLLA. I don't see why clk driver need to do something for the audio
>>> driver.
>
> Current ASoC driver already takes care of PLLA rate and enables.
>
> So PLLA init can be removed from clock driver too. I didn't went through
> complete audio driver to be confident to remove this.
>
> But PLLA is needed for i2s clock also and currently I2S driver takes
> care of only I2S clock rate using PLLA as parent set by clock driver and
> clock driver enables PLLA earlier to have it ready by the time both I2S
> driver and ASoC driver .
I2S could use assigned-clocks, but probably it's not really necessary
and predefined configuration in the clk driver is good enough.

At least PLLA doesn't need to be always-enabled since audio drivers
enable it when necessary.

\
 
 \ /
  Last update: 2019-12-08 00:25    [W:0.060 / U:32.828 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site