lkml.org 
[lkml]   [2019]   [Dec]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 1/2] scsi: ufs: set device as default active power mode during initialization only
On 2019-12-31 12:22, Stanley Chu wrote:
> Hi Can,
>
>
>> Hi Stanley,
>>
>> I see skipping ufshcd_set_ufs_dev_active() in ufshcd_probe_hba()
>> if it is called from ufshcd_resume() path is the purpose here.
>>
>> If so, then ufshcd_set_dev_pwr_mode() would be called, meaning
>> SSU command will be sent. Why is this SSU command needed to be
>> sent after a full host reset and restore? Is ufshcd_probe_hba()
>> not enough to make UFS device fully functional?
>
> After resume (for both runtime resume and system resume), device power
> mode shall be back to "Active" to service incoming requests.
>
> I see two cases need device power mode transition during resume flow
> 1. Device Power Mode = Sleep
> 2. Device Power Mode = PowerDown
>
> For 1, ufshcd_probe_hba() is not invoked during resume flow,
> hba->curr_dev_pwr_mode = SLEEP, thus ufshcd_resume() can invoke
> ufshcd_set_dev_pwr_mode() to change device power mode.
>
> For 2, ufshcd_probe_hba() is invoked during resume flow, before this
> fix, hba->curr_dev_pwr_mode will be set to ACTIVE (note that only this
> flag is set as ACTIVE, but device may be still in PowerDown state if
> device power is not fully shutdown or device HW reset is not executed
> before resume), in the end, ufshcd_resume() will not invoke
> ufshcd_set_dev_pwr_mode() to send SSU command to make device change
> back
> to Active power mode.

Hi Stanley,

Isn't below change fixing the problem you are saying above?
With it, after ufshcd_link_startup(), UFS device's power mode will
become Active anyways. Do you mean below change is not working properly
and you are removing it?

commit 7caf489b99a42a9017ef3d733912aea8794677e7
Author: subhashj@codeaurora.org <subhashj@codeaurora.org>
Date: Wed Nov 23 16:32:20 2016 -0800

scsi: ufs: issue link starup 2 times if device isn't active

If we issue the link startup to the device while its UniPro state is
LinkDown (and device state is sleep/power-down) then link startup
will not move the device state to Active. Device will only move to
active state if the link starup is issued when its UniPro state is
LinkUp. So in this case, we would have to issue the link startup 2
times to make sure that device moves to active state.

Thanks,

Can Guo

>
> But if device is fully reset before resume (not by current mainstream
> driver), device can be already in "Active" power mode after power on
> again during resume flow. In this case, it is OK to set
> hba->curr_dev_pwr_mode as ACTIVE in ufshcd_probe_hba() and SSU command
> is not necessary.
>
> Thanks,
> Stanley
>
>> _______________________________________________
>> Linux-mediatek mailing list
>> Linux-mediatek@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-mediatek

\
 
 \ /
  Last update: 2019-12-31 09:06    [W:0.045 / U:4.824 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site