lkml.org 
[lkml]   [2019]   [Dec]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [v12 2/2] clk: ls1028a: Add clock driver for Display output interface
Date


> -----Original Message-----
> From: Wen He <wen.he_1@nxp.com>
> Sent: 2019年12月13日 16:34
> To: Michael Turquette <mturquette@baylibre.com>; Stephen Boyd
> <sboyd@kernel.org>; Rob Herring <robh+dt@kernel.org>; Mark Rutland
> <mark.rutland@arm.com>; Michael Walle <michael@walle.cc>; Leo Li
> <leoyang.li@nxp.com>; devicetree@vger.kernel.org; linux-clk@vger.kernel.org;
> linux-kernel@vger.kernel.org
> Cc: Wen He <wen.he_1@nxp.com>
> Subject: [v12 2/2] clk: ls1028a: Add clock driver for Display output interface
>

Hi Maintainer,

Do you have any comments for this version?

Best Regards,
We

> Add clock driver for QorIQ LS1028A Display output interfaces(LCD, DPHY), as
> implemented in TSMC CLN28HPM PLL, this PLL supports the programmable
> integer division and range of the display output pixel clock's 27-594MHz.
>
> Signed-off-by: Wen He <wen.he_1@nxp.com>
> Signed-off-by: Michael Walle <michael@walle.cc>
> ---
> drivers/clk/Kconfig | 10 ++
> drivers/clk/Makefile | 1 +
> drivers/clk/clk-plldig.c | 286
> +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 297 insertions(+)
> create mode 100644 drivers/clk/clk-plldig.c
>
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig index
> 0530bebfc25a..9f6b0196c604 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -218,6 +218,16 @@ config CLK_QORIQ
> This adds the clock driver support for Freescale QorIQ platforms
> using common clock framework.
>
> +config CLK_LS1028A_PLLDIG
> + tristate "Clock driver for LS1028A Display output"
> + depends on ARCH_LAYERSCAPE || COMPILE_TEST
> + default ARCH_LAYERSCAPE
> + help
> + This driver support the Display output interfaces(LCD, DPHY) pixel
> clocks
> + of the QorIQ Layerscape LS1028A, as implemented TSMC
> CLN28HPM PLL. Not all
> + features of the PLL are currently supported by the driver. By
> default,
> + configured bypass mode with this PLL.
> +
> config COMMON_CLK_XGENE
> bool "Clock driver for APM XGene SoC"
> default ARCH_XGENE
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile index
> 0138fb14e6f8..97d1e5bc6de5 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -43,6 +43,7 @@ obj-$(CONFIG_ARCH_NPCM7XX) +=
> clk-npcm7xx.o
> obj-$(CONFIG_ARCH_NSPIRE) += clk-nspire.o
> obj-$(CONFIG_COMMON_CLK_OXNAS) += clk-oxnas.o
> obj-$(CONFIG_COMMON_CLK_PALMAS) += clk-palmas.o
> +obj-$(CONFIG_CLK_LS1028A_PLLDIG) += clk-plldig.o
> obj-$(CONFIG_COMMON_CLK_PWM) += clk-pwm.o
> obj-$(CONFIG_CLK_QORIQ) += clk-qoriq.o
> obj-$(CONFIG_COMMON_CLK_RK808) += clk-rk808.o
> diff --git a/drivers/clk/clk-plldig.c b/drivers/clk/clk-plldig.c new file mode
> 100644 index 000000000000..a5da08f98d01
> --- /dev/null
> +++ b/drivers/clk/clk-plldig.c
> @@ -0,0 +1,286 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright 2019 NXP
> + *
> + * Clock driver for LS1028A Display output interfaces(LCD, DPHY).
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/device.h>
> +#include <linux/module.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/bitfield.h>
> +
> +/* PLLDIG register offsets and bit masks */
> +#define PLLDIG_REG_PLLSR 0x24
> +#define PLLDIG_LOCK_MASK BIT(2)
> +#define PLLDIG_REG_PLLDV 0x28
> +#define PLLDIG_MFD_MASK GENMASK(7, 0)
> +#define PLLDIG_RFDPHI1_MASK GENMASK(30, 25)
> +#define PLLDIG_REG_PLLFM 0x2c
> +#define PLLDIG_SSCGBYP_ENABLE BIT(30)
> +#define PLLDIG_REG_PLLFD 0x30
> +#define PLLDIG_FDEN BIT(30)
> +#define PLLDIG_FRAC_MASK GENMASK(15, 0)
> +#define PLLDIG_REG_PLLCAL1 0x38
> +#define PLLDIG_REG_PLLCAL2 0x3c
> +
> +/* Range of the VCO frequencies, in Hz */
> +#define PLLDIG_MIN_VCO_FREQ 650000000
> +#define PLLDIG_MAX_VCO_FREQ 1300000000
> +
> +/* Range of the output frequencies, in Hz */
> +#define PHI1_MIN_FREQ 27000000
> +#define PHI1_MAX_FREQ 600000000
> +
> +/* Maximum value of the reduced frequency divider */
> +#define MAX_RFDPHI1 63UL
> +
> +/* Best value of multiplication factor divider */
> +#define PLLDIG_DEFAULT_MFD 44
> +
> +/*
> + * Denominator part of the fractional part of the
> + * loop multiplication factor.
> + */
> +#define MFDEN 20480
> +
> +static const struct clk_parent_data parent_data[] = {
> + { .index = 0 },
> +};
> +
> +struct clk_plldig {
> + struct clk_hw hw;
> + void __iomem *regs;
> + unsigned int vco_freq;
> +};
> +
> +#define to_clk_plldig(_hw) container_of(_hw, struct clk_plldig, hw)
> +
> +static int plldig_enable(struct clk_hw *hw) {
> + struct clk_plldig *data = to_clk_plldig(hw);
> + u32 val;
> +
> + val = readl(data->regs + PLLDIG_REG_PLLFM);
> + /*
> + * Use Bypass mode with PLL off by default, the frequency overshoot
> + * detector output was disable. SSCG Bypass mode should be enable.
> + */
> + val |= PLLDIG_SSCGBYP_ENABLE;
> + writel(val, data->regs + PLLDIG_REG_PLLFM);
> +
> + return 0;
> +}
> +
> +static void plldig_disable(struct clk_hw *hw) {
> + struct clk_plldig *data = to_clk_plldig(hw);
> + u32 val;
> +
> + val = readl(data->regs + PLLDIG_REG_PLLFM);
> +
> + val &= ~PLLDIG_SSCGBYP_ENABLE;
> + val |= FIELD_PREP(PLLDIG_SSCGBYP_ENABLE, 0x0);
> +
> + writel(val, data->regs + PLLDIG_REG_PLLFM); }
> +
> +static int plldig_is_enabled(struct clk_hw *hw) {
> + struct clk_plldig *data = to_clk_plldig(hw);
> +
> + return readl(data->regs + PLLDIG_REG_PLLFM) &
> + PLLDIG_SSCGBYP_ENABLE;
> +}
> +
> +static unsigned long plldig_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + struct clk_plldig *data = to_clk_plldig(hw);
> + u32 val, rfdphi1;
> +
> + val = readl(data->regs + PLLDIG_REG_PLLDV);
> +
> + /* Check if PLL is bypassed */
> + if (val & PLLDIG_SSCGBYP_ENABLE)
> + return parent_rate;
> +
> + rfdphi1 = FIELD_GET(PLLDIG_RFDPHI1_MASK, val);
> +
> + /*
> + * If RFDPHI1 has a value of 1 the VCO frequency is also divided by
> + * one.
> + */
> + if (!rfdphi1)
> + rfdphi1 = 1;
> +
> + return DIV_ROUND_UP(data->vco_freq, rfdphi1); }
> +
> +static unsigned long plldig_calc_target_div(unsigned long vco_freq,
> + unsigned long target_rate)
> +{
> + unsigned long div;
> +
> + div = DIV_ROUND_CLOSEST(vco_freq, target_rate);
> + div = clamp(div, 1UL, MAX_RFDPHI1);
> +
> + return div;
> +}
> +
> +static int plldig_determine_rate(struct clk_hw *hw,
> + struct clk_rate_request *req)
> +{
> + struct clk_plldig *data = to_clk_plldig(hw);
> + unsigned int div;
> +
> + req->rate = clamp(req->rate, PHI1_MIN_FREQ, PHI1_MAX_FREQ);
> + div = plldig_calc_target_div(data->vco_freq, req->rate);
> + req->rate = DIV_ROUND_UP(data->vco_freq, div);
> +
> + return 0;
> +}
> +
> +static int plldig_set_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long parent_rate)
> +{
> + struct clk_plldig *data = to_clk_plldig(hw);
> + unsigned int val, cond;
> + unsigned int rfdphi1;
> +
> + rate = clamp(rate, PHI1_MIN_FREQ, PHI1_MAX_FREQ);
> + rfdphi1 = plldig_calc_target_div(data->vco_freq, rate);
> +
> + /* update the divider value */
> + val = readl(data->regs + PLLDIG_REG_PLLDV);
> + val &= ~PLLDIG_RFDPHI1_MASK;
> + val |= FIELD_PREP(PLLDIG_RFDPHI1_MASK, rfdphi1);
> + writel(val, data->regs + PLLDIG_REG_PLLDV);
> +
> + /* waiting for old lock state to clear */
> + udelay(200);
> +
> + /* Wait until PLL is locked or timeout */
> + return readl_poll_timeout_atomic(data->regs + PLLDIG_REG_PLLSR, cond,
> + cond & PLLDIG_LOCK_MASK, 0,
> + USEC_PER_MSEC);
> +}
> +
> +static const struct clk_ops plldig_clk_ops = {
> + .enable = plldig_enable,
> + .disable = plldig_disable,
> + .is_enabled = plldig_is_enabled,
> + .recalc_rate = plldig_recalc_rate,
> + .determine_rate = plldig_determine_rate,
> + .set_rate = plldig_set_rate,
> +};
> +
> +static int plldig_init(struct clk_hw *hw) {
> + struct clk_plldig *data = to_clk_plldig(hw);
> + struct clk_hw *parent = clk_hw_get_parent(hw);
> + unsigned long parent_rate = clk_hw_get_rate(parent);
> + unsigned long val;
> + unsigned long long lltmp;
> + unsigned int mfd, fracdiv = 0;
> +
> + if (!parent)
> + return -EINVAL;
> +
> + if (data->vco_freq) {
> + mfd = data->vco_freq / parent_rate;
> + lltmp = data->vco_freq % parent_rate;
> + lltmp *= MFDEN;
> + do_div(lltmp, parent_rate);
> + fracdiv = lltmp;
> + } else {
> + mfd = PLLDIG_DEFAULT_MFD;
> + data->vco_freq = parent_rate * mfd;
> + }
> +
> + val = FIELD_PREP(PLLDIG_MFD_MASK, mfd);
> + writel(val, data->regs + PLLDIG_REG_PLLDV);
> +
> + /* Enable fractional divider */
> + if (fracdiv) {
> + val = FIELD_PREP(PLLDIG_FRAC_MASK, fracdiv);
> + val |= PLLDIG_FDEN;
> + writel(val, data->regs + PLLDIG_REG_PLLFD);
> + }
> +
> + return 0;
> +}
> +
> +static int plldig_clk_probe(struct platform_device *pdev) {
> + struct clk_plldig *data;
> + struct device *dev = &pdev->dev;
> + int ret;
> +
> + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + data->regs = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(data->regs))
> + return PTR_ERR(data->regs);
> +
> + data->hw.init = CLK_HW_INIT_PARENTS_DATA("dpclk",
> + parent_data,
> + &plldig_clk_ops,
> + 0);
> +
> + ret = devm_clk_hw_register(dev, &data->hw);
> + if (ret) {
> + dev_err(dev, "failed to register %s clock\n",
> + dev->of_node->name);
> + return ret;
> + }
> +
> + ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
> + &data->hw);
> + if (ret) {
> + dev_err(dev, "unable to add clk provider\n");
> + return ret;
> + }
> +
> + /*
> + * The frequency of the VCO cannot be changed during runtime.
> + * Therefore, let the user specify a desired frequency.
> + */
> + if (!of_property_read_u32(dev->of_node, "fsl,vco-hz",
> + &data->vco_freq)) {
> + if (data->vco_freq < PLLDIG_MIN_VCO_FREQ ||
> + data->vco_freq > PLLDIG_MAX_VCO_FREQ)
> + return -EINVAL;
> + }
> +
> + return plldig_init(&data->hw);
> +}
> +
> +static const struct of_device_id plldig_clk_id[] = {
> + { .compatible = "fsl,ls1028a-plldig" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, plldig_clk_id);
> +
> +static struct platform_driver plldig_clk_driver = {
> + .driver = {
> + .name = "plldig-clock",
> + .of_match_table = plldig_clk_id,
> + },
> + .probe = plldig_clk_probe,
> +};
> +module_platform_driver(plldig_clk_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Wen He <wen.he_1@nxp.com>");
> MODULE_DESCRIPTION("LS1028A
> +Display output interface pixel clock driver");
> --
> 2.17.1

\
 
 \ /
  Last update: 2019-12-30 13:52    [W:0.061 / U:29.540 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site