lkml.org 
[lkml]   [2019]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.19 102/321] microblaze: adjust the help to the real behavior
Date
From: Masahiro Yamada <yamada.masahiro@socionext.com>

[ Upstream commit bafcc61d998c1ca18f556d92a0e95335ac68c7da ]

"make ARCH=microblaze help" mentions simpleImage.<dt>.unstrip,
but it is not a real Make target. It does not work because Makefile
assumes "system.unstrip" is the name of DT.

$ make ARCH=microblaze CROSS_COMPILE=microblaze-linux- simpleImage.system.unstrip
[ snip ]
make[1]: *** No rule to make target 'arch/microblaze/boot/dts/system.unstrip.dtb', needed by 'arch/microblaze/boot/dts/system.dtb'. Stop.
make: *** [Makefile;1060: arch/microblaze/boot/dts] Error 2
make: *** Waiting for unfinished jobs....

simpleImage.<dt> works like a phony target that generates multiple
images. Reflect the real behavior. I removed the DT directory path
information because it is already explained a few lines below.

While I am here, I deleted the redundant *_defconfig explanation.

The top-level Makefile caters to list available defconfig files:

mmu_defconfig - Build for mmu
nommu_defconfig - Build for nommu

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/microblaze/Makefile | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/microblaze/Makefile b/arch/microblaze/Makefile
index 4f3ab57072652..eecf37276521c 100644
--- a/arch/microblaze/Makefile
+++ b/arch/microblaze/Makefile
@@ -91,11 +91,11 @@ define archhelp
echo '* linux.bin - Create raw binary'
echo ' linux.bin.gz - Create compressed raw binary'
echo ' linux.bin.ub - Create U-Boot wrapped raw binary'
- echo ' simpleImage.<dt> - ELF image with $(arch)/boot/dts/<dt>.dts linked in'
- echo ' - stripped elf with fdt blob'
- echo ' simpleImage.<dt>.unstrip - full ELF image with fdt blob'
- echo ' *_defconfig - Select default config from arch/microblaze/configs'
- echo ''
+ echo ' simpleImage.<dt> - Create the following images with <dt>.dtb linked in'
+ echo ' simpleImage.<dt> : raw image'
+ echo ' simpleImage.<dt>.ub : raw image with U-Boot header'
+ echo ' simpleImage.<dt>.unstrip: ELF (identical to vmlinux)'
+ echo ' simpleImage.<dt>.strip : stripped ELF'
echo ' Targets with <dt> embed a device tree blob inside the image'
echo ' These targets support board with firmware that does not'
echo ' support passing a device tree directly. Replace <dt> with the'
--
2.20.1


\
 
 \ /
  Last update: 2019-12-04 00:06    [W:0.906 / U:45.212 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site