lkml.org 
[lkml]   [2019]   [Dec]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v7 08/12] dt-bindings: dma: ti: Add document for K3 UDMA
On 09-12-19, 11:43, Peter Ujfalusi wrote:
> New binding document for
> Texas Instruments K3 NAVSS Unified DMA – Peripheral Root Complex (UDMA-P).
>
> UDMA-P is introduced as part of the K3 architecture and can be found in
> AM654 and j721e.
>
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> .../devicetree/bindings/dma/ti/k3-udma.yaml | 185 ++++++++++++++++++
> 1 file changed, 185 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/dma/ti/k3-udma.yaml
>
> diff --git a/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml b/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml
> new file mode 100644
> index 000000000000..77aef4a4abce
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/ti/k3-udma.yaml
> @@ -0,0 +1,185 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/dma/ti/k3-udma.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments K3 NAVSS Unified DMA Device Tree Bindings
> +
> +maintainers:
> + - Peter Ujfalusi <peter.ujfalusi@ti.com>
> +
> +description: |
> + The UDMA-P is intended to perform similar (but significantly upgraded)
> + functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P
> + module supports the transmission and reception of various packet types.
> + The UDMA-P is architected to facilitate the segmentation and reassembly of

How about:

The UDMA-P architecture facilitates the segmentation...

> + SoC DMA data structure compliant packets to/from smaller data blocks that are
> + natively compatible with the specific requirements of each connected
> + peripheral.
> + Multiple Tx and Rx channels are provided within the DMA which allow multiple
> + segmentation or reassembly operations to be ongoing. The DMA controller
> + maintains state information for each of the channels which allows packet
> + segmentation and reassembly operations to be time division multiplexed between
> + channels in order to share the underlying DMA hardware. An external DMA
> + scheduler is used to control the ordering and rate at which this multiplexing
> + occurs for Transmit operations. The ordering and rate of Receive operations
> + is indirectly controlled by the order in which blocks are pushed into the DMA
> + on the Rx PSI-L interface.
> +
> + The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
> + channels. Channels in the UDMA-P can be configured to be either Packet-Based
> + or Third-Party channels on a channel by channel basis.
> +
> + All transfers within NAVSS is done between PSI-L source and destination
> + threads.
> + The peripherals serviced by UDMA can be PSI-L native (sa2ul, cpsw, etc) or
> + legacy, non PSI-L native peripherals. In the later case a special, small PDMA
> + is tasked to act as a bridge between the PSI-L fabric and the legacy
> + peripheral.
> +
> + PDMAs can be configured via UDMAP peer registers to match with the
> + configuration of the legacy peripheral.
> +
> +allOf:
> + - $ref: "../dma-controller.yaml#"
> +
> +properties:
> + "#dma-cells":
> + const: 1
> + description: |
> + The cell is the PSI-L thread ID of the remote (to UDMAP) end.
> + Valid ranges for thread ID depends on the data movement direction:
> + for source thread IDs (rx): 0 - 0x7fff
> + for destination thread IDs (tx): 0x8000 - 0xffff
> +
> + PLease refer to the device documentation for the PSI-L thread map and also

s/PLease/Please

--
~Vinod

\
 
 \ /
  Last update: 2019-12-23 07:54    [W:0.150 / U:6.612 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site