lkml.org 
[lkml]   [2019]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCHv3 05/15] remoteproc/omap: Add the rproc ops .da_to_va() implementation
On Thu, 19 Dec 2019 at 19:34, Suman Anna <s-anna@ti.com> wrote:
>
> On 12/19/19 6:12 PM, Mathieu Poirier wrote:
> > On Thu, 19 Dec 2019 at 06:18, Tero Kristo <t-kristo@ti.com> wrote:
> >>
> >> On 18/12/2019 02:38, Mathieu Poirier wrote:
> >>> On Fri, Dec 13, 2019 at 02:55:27PM +0200, Tero Kristo wrote:
> >>>> From: Suman Anna <s-anna@ti.com>
> >>>>
> >>>> An implementation for the rproc ops .da_to_va() has been added
> >>>> that provides the address translation between device addresses
> >>>> to kernel virtual addresses for internal RAMs present on that
> >>>> particular remote processor device. The implementation provides
> >>>> the translations based on the addresses parsed and stored during
> >>>> the probe.
> >>>>
> >>>> This ops gets invoked by the exported rproc_da_to_va() function
> >>>> and allows the remoteproc core's ELF loader to be able to load
> >>>> program data directly into the internal memories.
> >>>>
> >>>> Signed-off-by: Suman Anna <s-anna@ti.com>
> >>>> Signed-off-by: Tero Kristo <t-kristo@ti.com>
> >>>> ---
> >>>> drivers/remoteproc/omap_remoteproc.c | 39 ++++++++++++++++++++++++++++
> >>>> 1 file changed, 39 insertions(+)
> >>>>
> >>>> diff --git a/drivers/remoteproc/omap_remoteproc.c b/drivers/remoteproc/omap_remoteproc.c
> >>>> index 844703507a74..28f14e24b389 100644
> >>>> --- a/drivers/remoteproc/omap_remoteproc.c
> >>>> +++ b/drivers/remoteproc/omap_remoteproc.c
> >>>> @@ -232,10 +232,49 @@ static int omap_rproc_stop(struct rproc *rproc)
> >>>> return 0;
> >>>> }
> >>>>
> >>>> +/**
> >>>> + * omap_rproc_da_to_va() - internal memory translation helper
> >>>> + * @rproc: remote processor to apply the address translation for
> >>>> + * @da: device address to translate
> >>>> + * @len: length of the memory buffer
> >>>> + *
> >>>> + * Custom function implementing the rproc .da_to_va ops to provide address
> >>>> + * translation (device address to kernel virtual address) for internal RAMs
> >>>> + * present in a DSP or IPU device). The translated addresses can be used
> >>>> + * either by the remoteproc core for loading, or by any rpmsg bus drivers.
> >>>> + * Returns the translated virtual address in kernel memory space, or NULL
> >>>> + * in failure.
> >>>> + */
> >>>> +static void *omap_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
> >>>> +{
> >>>> + struct omap_rproc *oproc = rproc->priv;
> >>>> + int i;
> >>>> + u32 offset;
> >>>> +
> >>>> + if (len <= 0)
> >>>> + return NULL;
> >>>> +
> >>>> + if (!oproc->num_mems)
> >>>> + return NULL;
> >>>> +
> >>>> + for (i = 0; i < oproc->num_mems; i++) {
> >>>> + if (da >= oproc->mem[i].dev_addr && da + len <=
> >>>
> >>> Shouldn't this be '<' rather than '<=' ?
> >>
> >> No, I think <= is correct. You need to consider the initial byte in the
> >> range also. Consider a simple case where you provide the exact da + len
> >> corresponding to a specific memory range.
> >
> > For that specific case you are correct. On the flip side if @da falls
> > somewhere after @mem[i].dev_addr, there is a possibility to clobber
> > the first byte of the next range if <= is used.
>
> Not really, you will miss out on the last byte actually if you use just
> <. This is just address range check, any memcpy would actually end one
> byte before.

I am indeed worried about actual memory accesses but rproc_da_to_va()
is using the same logic as you are when circling through carveouts.
As such you can forget about my comment.

Thanks,
Mathieu

>
> Eg: 0x80000 of len 0x10000. I should perfectly be able to copy 0x1000
> bytes at 0x8f000.
>
> regards
> Suman
>
>
> >
> > Thanks,
> > Mathieu
> >
> >>
> >>>
> >>>> + oproc->mem[i].dev_addr + oproc->mem[i].size) {
> >>>
> >>> One space too many after the '+' .
> >>
> >> True, I wonder why checkpatch did not catch this.
> >>
> >>>
> >>>> + offset = da - oproc->mem[i].dev_addr;
> >>>
> >>> One space too many after then '-' .
> >>
> >> Same, will fix these two.
> >>
> >> -Tero
> >>
> >>>
> >>>> + /* __force to make sparse happy with type conversion */
> >>>> + return (__force void *)(oproc->mem[i].cpu_addr +
> >>>> + offset);
> >>>> + }
> >>>> + }
> >>>> +
> >>>> + return NULL;
> >>>> +}
> >>>> +
> >>>> static const struct rproc_ops omap_rproc_ops = {
> >>>> .start = omap_rproc_start,
> >>>> .stop = omap_rproc_stop,
> >>>> .kick = omap_rproc_kick,
> >>>> + .da_to_va = omap_rproc_da_to_va,
> >>>> };
> >>>>
> >>>> static const char * const ipu_mem_names[] = {
> >>>> --
> >>>> 2.17.1
> >>>>
> >>>> --
> >>
> >> --
> >> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
>

\
 
 \ /
  Last update: 2019-12-20 23:17    [W:0.056 / U:5.788 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site