lkml.org 
[lkml]   [2019]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 5/5] arm64: dts: qcom: msm8998: Add ADSP, MPSS and SLPI nodes
On Fri 20 Dec 06:33 PST 2019, Jeffrey Hugo wrote:

> On Fri, Dec 20, 2019 at 12:00 AM Bjorn Andersson
> <bjorn.andersson@linaro.org> wrote:
> >
> > On Wed 18 Dec 05:22 PST 2019, Sibi Sankar wrote:
> >
> > > This patch adds ADSP, MPSS and SLPI nodes for MSM8998 SoCs.
> > >
> > > Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
> > > ---
> > > arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 8 ++
> > > arch/arm64/boot/dts/qcom/msm8998.dtsi | 124 ++++++++++++++++++++++
> > > 2 files changed, 132 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
> > > index 6db3f9e0344d1..e87094665c52c 100644
> > > --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
> > > @@ -312,6 +312,14 @@
> > > };
> > > };
> > >
> > > +&remoteproc_adsp {
> > > + status = "okay";
> > > +};
> > > +
> > > +&remoteproc_slpi {
> > > + status = "okay";
> > > +};
> > > +
> > > &tlmm {
> > > gpio-reserved-ranges = <0 4>, <81 4>;
> > > };
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> > > index 8d799e868a5d3..014127700afb0 100644
> > > --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> > > @@ -1075,6 +1075,61 @@
> > > #interrupt-cells = <0x2>;
> > > };
> > >
> > > + remoteproc_mss: remoteproc@4080000 {
> > > + compatible = "qcom,msm8998-mss-pil";
> > > + reg = <0x04080000 0x100>, <0x04180000 0x20>;
> > > + reg-names = "qdsp6", "rmb";
> > > +
> > > + interrupts-extended =
> > > + <&intc GIC_SPI 448 IRQ_TYPE_EDGE_RISING>,
> > > + <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > > + <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > > + <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > > + <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
> > > + <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
> > > + interrupt-names = "wdog", "fatal", "ready",
> > > + "handover", "stop-ack",
> > > + "shutdown-ack";
> > > +
> > > + clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
> > > + <&gcc GCC_BIMC_MSS_Q6_AXI_CLK>,
> > > + <&gcc GCC_BOOT_ROM_AHB_CLK>,
> > > + <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>,
> > > + <&gcc GCC_MSS_SNOC_AXI_CLK>,
> > > + <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
> > > + <&rpmcc RPM_SMD_QDSS_CLK>,
> > > + <&rpmcc RPM_SMD_XO_CLK_SRC>;
> >
> > RPM_SMD_XO_CLK_SRC doesn't seem to be implemented...
> >
> > I did pull in a patch from Jeff that defines it, but when I boot the
> > modem I see the following error repeatedly:
>
> Yeah, we need to figure out a solution for rpmcc to actually provide
> this since the previous N solutions were not acceptable. Its on my
> todo list to look into in Jan. However, I really think the DT should
> be defined this way, since it replicates the hardware config.
>

I presume you can't rely on parent_data due to issues before rpmcc has
probed properly?

Not sure what to do about that, perhaps we can stop-gap by adding the
new clock and setting up the DT, and then swing back to wiring it up
internally in gcc later?

> >
> > [ 616.632227] qcom-q6v5-mss 4080000.remoteproc: fatal error received: dog_hb.c:266:DOG_HB detects starvation of task 0xda172640, triage with its own
>
> Maybe the BIMC fix will address this?
>

Just applying "clk: qcom: smd: Add missing bimc clock" did not change
things.

So just to be clear, I'm testing this with the following patches on top
of linux-next:

clk: qcom: smd: Add missing bimc clock
clk: qcom: smd: Add XO clock for MSM8998
arm64: dts: msm8998: Add xo clock to gcc node
arm64: dts: qcom: msm8998: Add ADSP, MPSS and SLPI nodes
arm64: dts: qcom: msm8998: Update reserved memory map
remoteproc: qcom: pas: Add MSM8998 ADSP and SLPI support
dt-bindings: remoteproc: qcom: Add ADSP and SLPI support for MSM8998 SoC
remoteproc: q6v5-mss: Remove mem clk from the active pool
phy: qcom-qmp: Add optional SW reset
phy: qcom-qmp: Increase the phy init timeout

Regards,
Bjorn

> >
> >
> >
> > All the qrtr services seems registered nicely, so the remote does come
> > up before it goes down.
> >
> > Also, adsp comes up nicely.
> >
> > Regards,
> > Bjorn
> >
> > > + clock-names = "iface", "bus", "mem", "gpll0_mss",
> > > + "snoc_axi", "mnoc_axi", "qdss", "xo";
> > > +
> > > + qcom,smem-states = <&modem_smp2p_out 0>;
> > > + qcom,smem-state-names = "stop";
> > > +
> > > + resets = <&gcc GCC_MSS_RESTART>;
> > > + reset-names = "mss_restart";
> > > +
> > > + qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
> > > +
> > > + power-domains = <&rpmpd MSM8998_VDDCX>,
> > > + <&rpmpd MSM8998_VDDMX>;
> > > + power-domain-names = "cx", "mx";
> > > +
> > > + mba {
> > > + memory-region = <&mba_mem>;
> > > + };
> > > +
> > > + mpss {
> > > + memory-region = <&mpss_mem>;
> > > + };
> > > +
> > > + glink-edge {
> > > + interrupts = <GIC_SPI 452 IRQ_TYPE_EDGE_RISING>;
> > > + label = "modem";
> > > + qcom,remote-pid = <1>;
> > > + mboxes = <&apcs_glb 15>;
> > > + };
> > > + };
> > > +
> > > gpucc: clock-controller@5065000 {
> > > compatible = "qcom,msm8998-gpucc";
> > > #clock-cells = <1>;
> > > @@ -1088,6 +1143,42 @@
> > > "gpll0";
> > > };
> > >
> > > + remoteproc_slpi: remoteproc@5800000 {
> > > + compatible = "qcom,msm8998-slpi-pas";
> > > + reg = <0x05800000 0x4040>;
> > > +
> > > + interrupts-extended = <&intc GIC_SPI 390 IRQ_TYPE_EDGE_RISING>,
> > > + <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > > + <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > > + <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > > + <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> > > + interrupt-names = "wdog", "fatal", "ready",
> > > + "handover", "stop-ack";
> > > +
> > > + px-supply = <&vreg_lvs2a_1p8>;
> > > +
> > > + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
> > > + <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
> > > + clock-names = "xo", "aggre2";
> > > +
> > > + memory-region = <&slpi_mem>;
> > > +
> > > + qcom,smem-states = <&slpi_smp2p_out 0>;
> > > + qcom,smem-state-names = "stop";
> > > +
> > > + power-domains = <&rpmpd MSM8998_SSCCX>;
> > > + power-domain-names = "ssc_cx";
> > > +
> > > + status = "disabled";
> > > +
> > > + glink-edge {
> > > + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
> > > + label = "dsps";
> > > + qcom,remote-pid = <3>;
> > > + mboxes = <&apcs_glb 27>;
> > > + };
> > > + };
> > > +
> > > stm: stm@6002000 {
> > > compatible = "arm,coresight-stm", "arm,primecell";
> > > reg = <0x06002000 0x1000>,
> > > @@ -1880,6 +1971,39 @@
> > > #size-cells = <0>;
> > > };
> > >
> > > + remoteproc_adsp: remoteproc@17300000 {
> > > + compatible = "qcom,msm8998-adsp-pas";
> > > + reg = <0x17300000 0x4040>;
> > > +
> > > + interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
> > > + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > > + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > > + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > > + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> > > + interrupt-names = "wdog", "fatal", "ready",
> > > + "handover", "stop-ack";
> > > +
> > > + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
> > > + clock-names = "xo";
> > > +
> > > + memory-region = <&adsp_mem>;
> > > +
> > > + qcom,smem-states = <&adsp_smp2p_out 0>;
> > > + qcom,smem-state-names = "stop";
> > > +
> > > + power-domains = <&rpmpd MSM8998_VDDCX>;
> > > + power-domain-names = "cx";
> > > +
> > > + status = "disabled";
> > > +
> > > + glink-edge {
> > > + interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
> > > + label = "lpass";
> > > + qcom,remote-pid = <2>;
> > > + mboxes = <&apcs_glb 9>;
> > > + };
> > > + };
> > > +
> > > apcs_glb: mailbox@17911000 {
> > > compatible = "qcom,msm8998-apcs-hmss-global";
> > > reg = <0x17911000 0x1000>;
> > > --
> > > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> > > a Linux Foundation Collaborative Project

\
 
 \ /
  Last update: 2019-12-20 18:06    [W:0.057 / U:11.924 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site