lkml.org 
[lkml]   [2019]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v22 2/2] drm/bridge: Add I2C based driver for ps8640 bridge
On Fri, Dec 20, 2019 at 4:17 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> From: Jitao Shi <jitao.shi@mediatek.com>
>
> This patch adds drm_bridge driver for parade DSI to eDP bridge chip.
>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
> Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> [uli: followed API changes, removed FW update feature]
> Signed-off-by: Ulrich Hecht <uli@fpond.eu>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> ---
> [snip]
>
> drivers/gpu/drm/bridge/Kconfig | 11 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/parade-ps8640.c | 354 +++++++++++++++++++++++++

Half the size! Sounds great.

Mostly nits below.

> 3 files changed, 366 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/parade-ps8640.c
>
> diff --git a/drivers/gpu/drm/bridge/parade-ps8640.c b/drivers/gpu/drm/bridge/parade-ps8640.c
> new file mode 100644
> index 000000000000..aa0045037f44
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/parade-ps8640.c
> @@ -0,0 +1,354 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2016 MediaTek Inc.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of_graph.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <drm/drm_bridge.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_of.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_print.h>
> +
> +#define PAGE2_GPIO_H 0xa7
> +#define PS_GPIO9 BIT(1)
> +#define PAGE2_I2C_BYPASS 0xea
> +#define I2C_BYPASS_EN 0xd0
> +#define PAGE2_MCS_EN 0xf3
> +#define MCS_EN BIT(0)
> +#define PAGE3_SET_ADD 0xfe
> +#define VDO_CTL_ADD 0x13
> +#define VDO_DIS 0x18
> +#define VDO_EN 0x1c
> +
> +/*
> + * PS8640 uses multiple addresses:
> + * page[0]: for DP control
> + * page[1]: for VIDEO Bridge
> + * page[2]: for control top
> + * page[3]: for DSI Link Control1
> + * page[4]: for MIPI Phy
> + * page[5]: for VPLL
> + * page[6]: for DSI Link Control2
> + * page[7]: for SPI ROM mapping
> + */
> +enum page_addr_offset {
> + PAGE0_DP_CNTL = 0,
> + PAGE1_VDO_BDG,
> + PAGE2_TOP_CNTL,
> + PAGE3_DSI_CNTL1,
> + PAGE4_MIPI_PHY,
> + PAGE5_VPLL,
> + PAGE6_DSI_CNTL2,
> + PAGE7_SPI_CNTL,
> + MAX_DEVS
> +};
> +
> +struct ps8640 {
> + struct drm_bridge bridge;
> + struct drm_bridge *panel_bridge;
> + struct mipi_dsi_device *dsi;
> + struct i2c_client *page[MAX_DEVS];
> + struct regulator_bulk_data supplies[2];
> + struct gpio_desc *gpio_reset;
> + struct gpio_desc *gpio_powerdown;
> +};
> +
> +static inline struct ps8640 *bridge_to_ps8640(struct drm_bridge *e)
> +{
> + return container_of(e, struct ps8640, bridge);
> +}
> +
> +static int ps8640_bridge_unmute(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[PAGE3_DSI_CNTL1];
> + u8 vdo_ctrl_buf[] = { VDO_CTL_ADD, VDO_EN };

nit: const?

> + int ret;
> +
> + ret = i2c_smbus_write_i2c_block_data(client, PAGE3_SET_ADD,
> + sizeof(vdo_ctrl_buf),
> + vdo_ctrl_buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int ps8640_bridge_mute(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[PAGE3_DSI_CNTL1];
> + u8 vdo_ctrl_buf[] = { VDO_CTL_ADD, VDO_DIS };

ditto

> + int ret;
> +
> + ret = i2c_smbus_write_i2c_block_data(client, PAGE3_SET_ADD,
> + sizeof(vdo_ctrl_buf),
> + vdo_ctrl_buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}

Since the 2 functions are almost the same, you could shrink the driver
a bit further by merging them into one with a boolean parameter? (then
maybe give up on the const u8 comment).

> +
> +static void ps8640_pre_enable(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + struct i2c_client *client = ps_bridge->page[PAGE2_TOP_CNTL];
> + unsigned long timeout;
> + int ret, status;
> +
> + ret = regulator_bulk_enable(ARRAY_SIZE(ps_bridge->supplies),
> + ps_bridge->supplies);
> + if (ret < 0) {
> + DRM_ERROR("cannot enable regulators %d\n", ret);
> + return;
> + }
> +
> + gpiod_set_value(ps_bridge->gpio_powerdown, 1);
> + gpiod_set_value(ps_bridge->gpio_reset, 0);
> + usleep_range(2000, 2500);
> + gpiod_set_value(ps_bridge->gpio_reset, 1);
> +
> + /*
> + * Wait for the ps8640 embedded MCU to be ready
> + * First wait 200ms and then check the MCU ready flag every 20ms
> + */
> + msleep(200);
> +
> + timeout = jiffies + msecs_to_jiffies(200) + 1;
> +
> + while (time_is_after_jiffies(timeout)) {
> + status = i2c_smbus_read_byte_data(client, PAGE2_GPIO_H);
> + if (status < 0) {
> + DRM_ERROR("failed read PAGE2_GPIO_H: %d\n", status);
> + goto err_regulators_disable;
> + }
> + if ((status & PS_GPIO9) == PS_GPIO9)
> + break;
> +
> + msleep(20);
> + }
> +
> + msleep(50);
> +
> + /*
> + * The Manufacturer Command Set (MCS) is a device dependent interface
> + * intended for factory programming of the display module default
> + * parameters. Once the display module is configured, the MCS shall be
> + * disabled by the manufacturer. Once disabled, all MCS commands are
> + * ignored by the display interface.
> + */
> + status = i2c_smbus_read_byte_data(client, PAGE2_MCS_EN);
> + if (status < 0) {
> + DRM_ERROR("failed read PAGE2_MCS_EN: %d\n", status);
> + goto err_regulators_disable;
> + }
> +
> + ret = i2c_smbus_write_byte_data(client, PAGE2_MCS_EN,
> + status & ~MCS_EN);
> + if (ret < 0) {
> + DRM_ERROR("failed write PAGE2_MCS_EN: %d\n", ret);
> + goto err_regulators_disable;
> + }
> +
> + ret = ps8640_bridge_unmute(ps_bridge);
> + if (ret)
> + DRM_ERROR("failed to enable unmutevideo: %d\n", ret);

failed to unmute? Or failed to enable?

> +
> + /* Switch access edp panel's edid through i2c */
> + ret = i2c_smbus_write_byte_data(client, PAGE2_I2C_BYPASS,
> + I2C_BYPASS_EN);
> + if (ret < 0) {
> + DRM_ERROR("failed write PAGE2_I2C_BYPASS: %d\n", ret);
> + goto err_regulators_disable;
> + }
> +
> + return;
> +
> +err_regulators_disable:
> + regulator_bulk_disable(ARRAY_SIZE(ps_bridge->supplies),
> + ps_bridge->supplies);
> +}
> +
> +static void ps8640_post_disable(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + int ret;
> +
> + ret = ps8640_bridge_mute(ps_bridge);
> + if (ret < 0)
> + DRM_ERROR("failed to unmutevideo: %d\n", ret);

ditto

> +
> + gpiod_set_value(ps_bridge->gpio_reset, 0);
> + gpiod_set_value(ps_bridge->gpio_powerdown, 0);
> + ret = regulator_bulk_disable(ARRAY_SIZE(ps_bridge->supplies),
> + ps_bridge->supplies);
> + if (ret < 0)
> + DRM_ERROR("cannot disable regulators %d\n", ret);
> +}
> +
> +int ps8640_bridge_attach(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + struct device *dev = &ps_bridge->page[0]->dev;
> + struct device_node *in_ep, *dsi_node;
> + struct mipi_dsi_device *dsi;
> + struct mipi_dsi_host *host;
> + int ret;
> + const struct mipi_dsi_device_info info = { .type = "ps8640",
> + .channel = 0,
> + .node = NULL,
> + };
> + /* port@0 is ps8640 dsi input port */
> + in_ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, -1);
> + if (!in_ep)
> + return -ENODEV;
> +
> + dsi_node = of_graph_get_remote_port_parent(in_ep);
> + of_node_put(in_ep);
> + if (!dsi_node)
> + return -ENODEV;
> +
> + host = of_find_mipi_dsi_host_by_node(dsi_node);
> + of_node_put(dsi_node);
> + if (!host)
> + return -ENODEV;
> +
> + dsi = mipi_dsi_device_register_full(host, &info);
> + if (IS_ERR(dsi)) {
> + dev_err(dev, "failed to create dsi device\n");
> + ret = PTR_ERR(dsi);
> + return ret;
> + }
> +
> + ps_bridge->dsi = dsi;
> +
> + dsi->host = host;
> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
> + MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> + dsi->format = MIPI_DSI_FMT_RGB888;
> + dsi->lanes = 4;
> + ret = mipi_dsi_attach(dsi);
> + if (ret)
> + goto err_dsi_attach;
> +
> + /* Attach the panel-bridge to the dsi bridge */
> + return drm_bridge_attach(bridge->encoder, ps_bridge->panel_bridge,
> + &ps_bridge->bridge);
> +
> +err_dsi_attach:
> + mipi_dsi_device_unregister(dsi);
> + return ret;
> +}
> +
> +static const struct drm_bridge_funcs ps8640_bridge_funcs = {
> + .attach = ps8640_bridge_attach,
> + .post_disable = ps8640_post_disable,
> + .pre_enable = ps8640_pre_enable,
> +};
> +
> +static int ps8640_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct device_node *np = dev->of_node;
> + struct ps8640 *ps_bridge;
> + struct drm_panel *panel;
> + int ret;
> + u32 i;
> +
> + ps_bridge = devm_kzalloc(dev, sizeof(*ps_bridge), GFP_KERNEL);
> + if (!ps_bridge)
> + return -ENOMEM;
> +
> + /* port@1 is ps8640 output port */
> + ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL);
> + if (ret < 0)
> + return ret;
> + if (!panel)
> + return -ENODEV;
> +
> + panel->connector_type = DRM_MODE_CONNECTOR_eDP;
> +
> + ps_bridge->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
> + if (IS_ERR(ps_bridge->panel_bridge))
> + return PTR_ERR(ps_bridge->panel_bridge);
> +
> + ps_bridge->supplies[0].supply = "vdd33";
> + ps_bridge->supplies[1].supply = "vdd12";
> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ps_bridge->supplies),
> + ps_bridge->supplies);
> + if (ret)
> + return ret;
> +
> + ps_bridge->gpio_powerdown = devm_gpiod_get(&client->dev, "powerdown",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(ps_bridge->gpio_powerdown))
> + return PTR_ERR(ps_bridge->gpio_powerdown);
> +
> + /*
> + * Request the reset pin low to avoid the bridge being
> + * initialized prematurely
> + */
> + ps_bridge->gpio_reset = devm_gpiod_get(&client->dev, "reset",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(ps_bridge->gpio_reset))
> + return PTR_ERR(ps_bridge->gpio_reset);
> +
> + ps_bridge->bridge.funcs = &ps8640_bridge_funcs;
> + ps_bridge->bridge.of_node = dev->of_node;
> +
> + ps_bridge->page[PAGE0_DP_CNTL] = client;
> +
> + for (i = 1; i < ARRAY_SIZE(ps_bridge->page); i++) {
> + ps_bridge->page[i] = devm_i2c_new_dummy_device(&client->dev,
> + client->adapter,
> + client->addr + i);
> + if (IS_ERR(ps_bridge->page[i])) {
> + dev_err(dev, "failed i2c dummy device, address%02x\n",

Space after address?

> + client->addr + i);
> + return PTR_ERR(ps_bridge->page[i]);
> + }
> + }
> +
> + i2c_set_clientdata(client, ps_bridge);
> +
> + drm_bridge_add(&ps_bridge->bridge);
> +
> + return 0;
> +}
> +
> +static int ps8640_remove(struct i2c_client *client)
> +{
> + struct ps8640 *ps_bridge = i2c_get_clientdata(client);
> +
> + drm_bridge_remove(&ps_bridge->bridge);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ps8640_match[] = {
> + { .compatible = "parade,ps8640" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, ps8640_match);
> +
> +static struct i2c_driver ps8640_driver = {
> + .probe_new = ps8640_probe,
> + .remove = ps8640_remove,
> + .driver = {
> + .name = "ps8640",
> + .of_match_table = ps8640_match,
> + },
> +};
> +module_i2c_driver(ps8640_driver);
> +
> +MODULE_AUTHOR("Jitao Shi <jitao.shi@mediatek.com>");
> +MODULE_AUTHOR("CK Hu <ck.hu@mediatek.com>");

Since you just did a major refactor, do you want to add your name here?

> +MODULE_DESCRIPTION("PARADE ps8640 DSI-eDP converter driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.20.1
>

\
 
 \ /
  Last update: 2019-12-20 09:45    [W:0.056 / U:3.584 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site