lkml.org 
[lkml]   [2019]   [Dec]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2] arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card
On Sat, Dec 14, 2019 at 07:24:34AM +0530, Veerabhadrarao Badiganti wrote:
> Add sdhc instances for supporting eMMC and SD-card on sc7180.
> The regulators should be in HPM state for proper functionality of
> eMMC and SD-card. Updating corresponding regulators accordingly.
>
> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
> ---
>
> This depends on the patch series (dt support for sc7180):
> https://lkml.org/lkml/2019/11/8/149
> Also depends on documentation commit 2078158 (Present on mmc-next)
>
> Changes since V1:
> - Updated the regulator min, max voltages as per
> eMMC/SD-card voltage requirements
> - Enabled IOMMU for eMMC and SD-card.
> - Added pull and drive strength to SD-card cd-gpio.
> - Incorporated review comments by Matthias Kaehlcke.
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 47 +++++++---
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 148 ++++++++++++++++++++++++++++++++
> 2 files changed, 183 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 189254f..b6d4dc1 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -7,6 +7,7 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> #include "sc7180.dtsi"
> #include "pm6150.dtsi"
> @@ -101,9 +102,9 @@
> };
>
> vreg_l12a_1p8: ldo12 {
> - regulator-min-microvolt = <1696000>;
> - regulator-max-microvolt = <1952000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> vreg_l13a_1p8: ldo13 {
> @@ -143,9 +144,9 @@
> };
>
> vreg_l19a_2p9: ldo19 {
> - regulator-min-microvolt = <2696000>;
> - regulator-max-microvolt = <3304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
> };
>
> @@ -189,9 +190,9 @@
> };
>
> vreg_l6c_2p9: ldo6 {
> - regulator-min-microvolt = <2696000>;
> - regulator-max-microvolt = <3304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> vreg_l7c_3p0: ldo7 {
> @@ -207,9 +208,9 @@
> };
>
> vreg_l9c_2p9: ldo9 {
> - regulator-min-microvolt = <2952000>;
> - regulator-max-microvolt = <3304000>;
> - regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> };
>
> vreg_l10c_3p3: ldo10 {
> @@ -400,3 +401,25 @@
> bias-pull-up;
> };
> };
> +
> +&sdhc_1 {
> + status = "ok";

another nit: the DT code is fine with both "okay" and "ok", however
the rest of this file uses "okay", so let's be consistent and use the
same string in all nodes.

> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc1_on>;
> + pinctrl-1 = <&sdc1_off>;
> + vmmc-supply = <&vreg_l19a_2p9>;
> + vqmmc-supply = <&vreg_l12a_1p8>;
> +};
> +
> +&sdhc_2 {
> + status = "ok";

ditto

\
 
 \ /
  Last update: 2019-12-20 00:30    [W:0.114 / U:8.532 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site