lkml.org 
[lkml]   [2019]   [Dec]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] ARM: dts: exynos: Adjust bus related OPPs to the values correct for Odroids
From
Date
On 12/19/19 6:09 PM, Marek Szyprowski wrote:
> Hi Chanwoo,
>
> On 19.12.2019 10:07, Chanwoo Choi wrote:
>> On 12/19/19 5:29 PM, Marek Szyprowski wrote:
>>> Hardkernel's Odroid XU3/XU4/HC1 boards use bootloader, which configures top
>>> PLLs to the following values: MPLL: 532MHz, CPLL: 666MHz and DPLL: 600MHz.
>>>
>>> Adjust all bus related OPPs to the values that are possible to derive from
>>> the top PLL configured by the bootloader. Also add a comment for each bus
>>> describing which PLL is used for it.
>>>
>>> The most significant change is the highest rate for wcore bus. It has been
>>> increased to 532MHz as this is the value configured initially by the
>>> bootloader. Also the voltage for this OPP is changed to match the value
>>> set by the bootloader.
>>>
>>> This patch finally allows the buses to operate on the rates matching the
>>> values set for each OPP and fixes the following warnings observed on boot:
>>>
>>> exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
>>> exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
>>> exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz)
>>> ...
>>> exynos-bus soc:bus_wcore: dev_pm_opp_set_rate: failed to find current OPP for freq 532000000 (-34)
>>> exynos-bus soc:bus_noc: dev_pm_opp_set_rate: failed to find current OPP for freq 111000000 (-34)
>>> exynos-bus soc:bus_fsys_apb: dev_pm_opp_set_rate: failed to find current OPP for freq 222000000 (-34)
>>>
>>> The problem with setting incorrect (in some cases much lower) clock rate
>>> for the defined OPP were there from the beginning, but went unnoticed
>>> because the only way to observe it was to manually check the rate of the
>>> respective clocks. The commit 4294a779bd8d ("PM / devfreq: exynos-bus:
>>> Convert to use dev_pm_opp_set_rate()") finally revealed it, because it
>>> enabled use of the generic code from the OPP framework, which issues the
>>> above mentioned warnings.
>>>
>>> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
>>> ---
>>> arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 75 +++++++++++--------
>>> 1 file changed, 45 insertions(+), 30 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
>>> index 663a38d53c9e..b6d6022e8735 100644
>>> --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
>>> +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
>>> @@ -38,42 +38,44 @@
>>> bus_wcore_opp_table: opp_table2 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 532MHz MPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <84000000>;
>>> + opp-hz = /bits/ 64 <88700000>;
>>> opp-microvolt = <925000 925000 1400000>;
>>> };
>>> opp01 {
>>> - opp-hz = /bits/ 64 <111000000>;
>>> + opp-hz = /bits/ 64 <133000000>;
>>> opp-microvolt = <950000 950000 1400000>;
>>> };
>>> opp02 {
>>> - opp-hz = /bits/ 64 <222000000>;
>>> + opp-hz = /bits/ 64 <177400000>;
>>> opp-microvolt = <950000 950000 1400000>;
>>> };
>>> opp03 {
>>> - opp-hz = /bits/ 64 <333000000>;
>>> + opp-hz = /bits/ 64 <266000000>;
>>> opp-microvolt = <950000 950000 1400000>;
>>> };
>>> opp04 {
>>> - opp-hz = /bits/ 64 <400000000>;
>>> - opp-microvolt = <987500 987500 1400000>;
>>> + opp-hz = /bits/ 64 <532000000>;
>>> + opp-microvolt = <1000000 1000000 1400000>;
>>> };
>>> };
>>>
>>> bus_noc_opp_table: opp_table3 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <67000000>;
>>> + opp-hz = /bits/ 64 <66600000>;
>>> };
>>> opp01 {
>>> - opp-hz = /bits/ 64 <75000000>;
>>> + opp-hz = /bits/ 64 <74000000>;
>>> };
>>> opp02 {
>>> - opp-hz = /bits/ 64 <86000000>;
>>> + opp-hz = /bits/ 64 <83250000>;
>>> };
>>> opp03 {
>>> - opp-hz = /bits/ 64 <100000000>;
>>> + opp-hz = /bits/ 64 <111000000>;
>>> };
>>> };
>>>
>>> @@ -81,39 +83,42 @@
>>> compatible = "operating-points-v2";
>>> opp-shared;
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <100000000>;
>>> + opp-hz = /bits/ 64 <111000000>;
>>> };
>>> opp01 {
>>> - opp-hz = /bits/ 64 <200000000>;
>>> + opp-hz = /bits/ 64 <222000000>;
>>> };
>>> };
>>>
>>> bus_fsys2_opp_table: opp_table5 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 600MHz DPLL */
>>> opp00 {
>>> opp-hz = /bits/ 64 <75000000>;
>>> };
>>> opp01 {
>>> - opp-hz = /bits/ 64 <100000000>;
>>> + opp-hz = /bits/ 64 <120000000>;
>>> };
>>> opp02 {
>>> - opp-hz = /bits/ 64 <150000000>;
>>> + opp-hz = /bits/ 64 <200000000>;
>>> };
>>> };
>>>
>>> bus_mfc_opp_table: opp_table6 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <96000000>;
>>> + opp-hz = /bits/ 64 <83250000>;
>>> };
>>> opp01 {
>>> opp-hz = /bits/ 64 <111000000>;
>>> };
>>> opp02 {
>>> - opp-hz = /bits/ 64 <167000000>;
>>> + opp-hz = /bits/ 64 <166500000>;
>>> };
>>> opp03 {
>>> opp-hz = /bits/ 64 <222000000>;
>>> @@ -126,8 +131,9 @@
>>> bus_gen_opp_table: opp_table7 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 532MHz MPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <89000000>;
>>> + opp-hz = /bits/ 64 <88700000>;
>>> };
>>> opp01 {
>>> opp-hz = /bits/ 64 <133000000>;
>>> @@ -136,32 +142,34 @@
>>> opp-hz = /bits/ 64 <178000000>;
>>> };
>>> opp03 {
>>> - opp-hz = /bits/ 64 <267000000>;
>>> + opp-hz = /bits/ 64 <266000000>;
>>> };
>>> };
>>>
>>> bus_peri_opp_table: opp_table8 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <67000000>;
>>> + opp-hz = /bits/ 64 <66600000>;
>>> };
>>> };
>>>
>>> bus_g2d_opp_table: opp_table9 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <84000000>;
>>> + opp-hz = /bits/ 64 <83250000>;
>>> };
>>> opp01 {
>>> - opp-hz = /bits/ 64 <167000000>;
>>> + opp-hz = /bits/ 64 <111000000>;
>>> };
>>> opp02 {
>>> - opp-hz = /bits/ 64 <222000000>;
>>> + opp-hz = /bits/ 64 <166500000>;
>>> };
>>> opp03 {
>>> - opp-hz = /bits/ 64 <300000000>;
>>> + opp-hz = /bits/ 64 <222000000>;
>>> };
>>> opp04 {
>>> opp-hz = /bits/ 64 <333000000>;
>>> @@ -171,8 +179,9 @@
>>> bus_g2d_acp_opp_table: opp_table10 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 532MHz MPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <67000000>;
>>> + opp-hz = /bits/ 64 <66500000>;
>>> };
>>> opp01 {
>>> opp-hz = /bits/ 64 <133000000>;
>>> @@ -181,13 +190,14 @@
>>> opp-hz = /bits/ 64 <178000000>;
>>> };
>>> opp03 {
>>> - opp-hz = /bits/ 64 <267000000>;
>>> + opp-hz = /bits/ 64 <266000000>;
>>> };
>>> };
>>>
>>> bus_jpeg_opp_table: opp_table11 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 600MHz DPLL */
>>> opp00 {
>>> opp-hz = /bits/ 64 <75000000>;
>>> };
>>> @@ -205,23 +215,25 @@
>>> bus_jpeg_apb_opp_table: opp_table12 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> - opp-hz = /bits/ 64 <84000000>;
>>> + opp-hz = /bits/ 64 <83250000>;
>>> };
>>> opp01 {
>>> opp-hz = /bits/ 64 <111000000>;
>>> };
>>> opp02 {
>>> - opp-hz = /bits/ 64 <134000000>;
>>> + opp-hz = /bits/ 64 <133000000>;
>>> };
>>> opp03 {
>>> - opp-hz = /bits/ 64 <167000000>;
>>> + opp-hz = /bits/ 64 <166500000>;
>>> };
>>> };
>>>
>>> bus_disp1_fimd_opp_table: opp_table13 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 600MHz DPLL */
>>> opp00 {
>>> opp-hz = /bits/ 64 <120000000>;
>>> };
>>> @@ -233,6 +245,7 @@
>>> bus_disp1_opp_table: opp_table14 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 600MHz DPLL */
>>> opp00 {
>>> opp-hz = /bits/ 64 <120000000>;
>>> };
>>> @@ -247,6 +260,7 @@
>>> bus_gscl_opp_table: opp_table15 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 600MHz DPLL */
>>> opp00 {
>>> opp-hz = /bits/ 64 <150000000>;
>>> };
>>> @@ -261,6 +275,7 @@
>>> bus_mscl_opp_table: opp_table16 {
>>> compatible = "operating-points-v2";
>>>
>>> + /* derived from 666MHz CPLL */
>>> opp00 {
>>> opp-hz = /bits/ 64 <84000000>;
>>> };
>>> @@ -274,7 +289,7 @@
>>> opp-hz = /bits/ 64 <333000000>;
>>> };
>>> opp04 {
>>> - opp-hz = /bits/ 64 <400000000>;
>>> + opp-hz = /bits/ 64 <666000000>;
>>> };
>>> };
>>>
>>> @@ -398,7 +413,7 @@
>>> };
>>>
>>> &bus_fsys {
>>> - operating-points-v2 = <&bus_fsys_apb_opp_table>;
>>> + operating-points-v2 = <&bus_fsys2_opp_table>;
>>
>> Need to remove 'opp-shared' property in bus_fsys_apb_opp_table.
>> And need to add 'opp-shared' property to bus_fsys2_opp_table.
>
> I've checked the dt bindings and I think that opp-shared property has to
> be removed at all. Clocks between fsys and fsys2 buses are not related
> and regulator is currently already handled by in a different way by the
> passive governor.

You're right. I realized 'opp-shared' is not necessary
by reading Documentation/devicetree/bindings/opp/opp.txt. Thanks.

>
>>> devfreq = <&bus_wcore>;
>>> status = "okay";
>>> };
>>>
>> If you fix the things related to 'opp-shared', Looks good to me.
>> Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
>>
> Best regards
>


--
Best Regards,
Chanwoo Choi
Samsung Electronics

\
 
 \ /
  Last update: 2019-12-19 10:18    [W:0.043 / U:1.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site