lkml.org 
[lkml]   [2019]   [Dec]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 7/9] ARM: dts: ux500: samsung-golden: Add WiFi
Date
samsung-golden uses a BCM4334 WiFi+BT combo chip, connected to SDIO.
It is supported by the brcmfmac driver in mainline,
so we only need to set up the device tree to make it work correctly.

Note: brcmfmac requires (proprietary) firmware + a device-specific
NVRAM file. Both can be extracted from the stock Android system
used on samsung-golden:
- /system/etc/wifi/bcmdhd_sta.bin_b2 -> /lib/firmware/brcm/brcmfmac4334-sdio.bin
- /system/etc/wifi/nvram_net.txt_GPIO4 -> /lib/firmware/brcm/brcmfmac4334-sdio.samsung,golden.txt

brcmfmac4334-sdio.bin from linux-firmware also seems to work,
but results in occasional errors for some reason.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
.../arm/boot/dts/ste-ux500-samsung-golden.dts | 56 +++++++++++++++++++
1 file changed, 56 insertions(+)

diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
index e75a425d177e..d22b2879c46a 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
@@ -64,9 +64,27 @@ sdi1_per2@80118000 {
non-removable;
cap-sd-highspeed;

+ vmmc-supply = <&wl_reg_on>;
+
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mc1_a_2_default>;
pinctrl-1 = <&mc1_a_2_sleep>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ /* GPIO216 (WLAN_HOST_WAKE) */
+ interrupt-parent = <&gpio6>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_default>;
+ };
};

/* eMMC */
@@ -290,6 +308,28 @@ sd_level_translator: regulator-sd-level-translator {
pinctrl-names = "default";
pinctrl-0 = <&sd_level_translator_default>;
};
+
+ /*
+ * WL_REG_ON takes WLAN out of reset and enables the internal regulators.
+ * The voltage specified here is only used to determine the OCR mask,
+ * the BCM chip is actually connected directly to VBAT.
+ */
+ wl_reg_on: regulator-wl-reg-on {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg-on";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ startup-delay-us = <100000>;
+
+ /* GPIO215 (WLAN_EN) */
+ gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_en_default>;
+ };
};

&pinctrl {
@@ -340,6 +380,22 @@ golden_cfg1 {
};
};

+ wlan {
+ wlan_default: wlan_default {
+ golden_cfg1 {
+ pins = "GPIO216_AG12"; /* WLAN_HOST_WAKE */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+
+ wlan_en_default: wlan_en_default {
+ golden_cfg1 {
+ pins = "GPIO215_AH13"; /* WLAN_EN */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+
vibrator {
vibrator_default: vibrator_default {
golden_cfg1 {
--
2.24.1
\
 
 \ /
  Last update: 2019-12-19 21:22    [W:0.073 / U:1.752 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site