lkml.org 
[lkml]   [2019]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 2/2] spi: cadence-quadpsi: Add support for the Cadence QSPI controller
From
Date
Hi  Vigensh,

    Thanks for the review and guidance to improve the code a lot.

On 17/12/2019 12:25 PM, Vignesh Raghavendra wrote:
> Hi,
>
> On 09/12/19 2:10 pm, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>
>> Add support for the Cadence QSPI controller. This controller is
>> present in the Intel Lightning Mountain(LGM) SoCs, Altera and TI SoCs.
>> This driver has been tested on the Intel LGM SoCs.
>>
>> This driver does not support generic SPI and also the implementation
>> only supports spi-mem interface to replace the existing driver in
>> mtd/spi-nor/cadence-quadspi.c, the existing driver only support SPI-NOR
>> flash memory.
>>
> Patch looks much better.. I will try to test this patch on TI
> platforms... Thanks for doing this! Comments inline...
Thank you :-)
>> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>> ---
> [...]
>> +
>> +static int cqspi_indirect_write_execute(struct struct_cqspi *cqspi,
>> + const struct spi_mem_op *op,
>> + const u8 *txbuf)
>> +{
>> + struct platform_device *pdev = cqspi->pdev;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> + struct cqspi_flash_pdata *f_pdata =
>> + &pdata->f_pdata[cqspi->current_cs];
>> + void *reg_base = cqspi->iobase;
>> + void *ahb_base = cqspi->qspi_ahb_virt;
>> + u32 page_size = f_pdata->page_size;
>> + u32 write_bytes, reg = 0;
>> + int remaining = op->data.nbytes;
>> + int ret;
>> +
>> + writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
> Does this needs to be done for every write? Can this be moved to
> cqspi_controller_init(). Also use a macro for constants
>
>> + writel(0x0, reg_base + CQSPI_REG_INDIRECTWRWATERMARK);
> This looks wrong. This was previously set to (cqspi->fifo_depth *
> cqspi->fifo_width / 2). Why do you need to set this to 0? If this needs
> to be 0, setup DT properties as required.
Let me check once it is required or not, then moved to

cqspi_controller_init() function.

>> + reg = readl(reg_base + CQSPI_REG_SIZE);
>> + reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
>> + reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
>> + reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
>> + reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
>> + writel(reg, reg_base + CQSPI_REG_SIZE);
>> +
>> + writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES);
>> + writel(CQSPI_REG_SRAM_PARTITION_WR, reg_base + CQSPI_REG_SRAMPARTITION);
>> + /* Clear all interrupts. */
>> + writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
>> + writel(CQSPI_IRQ_MASK_WR, reg_base + CQSPI_REG_IRQMASK);
>> + reinit_completion(&cqspi->transfer_complete);
>> + writel(CQSPI_REG_INDIRECTWR_START_MASK,
>> + reg_base + CQSPI_REG_INDIRECTWR);
>> +
>> + if (cqspi->wr_delay)
>> + ndelay(cqspi->wr_delay);
>> +
>> + while (remaining > 0) {
>> + size_t write_words, mod_bytes;
>> +
>> + write_bytes = remaining > page_size ? page_size : remaining;
>> + write_words = write_bytes / 4;
>> + mod_bytes = write_bytes % 4;
>> +
>> + if (write_words) {
>> + iowrite32_rep(ahb_base, txbuf, write_words);
>> + txbuf += (write_words * 4);
>> + }
>> + if (mod_bytes) {
>> + unsigned int temp = 0xFFFFFFFF;
>> +
>> + memcpy(&temp, txbuf, mod_bytes);
>> + iowrite32(temp, ahb_base);
>> + txbuf += mod_bytes;
>> + }
>> + if (!wait_for_completion_timeout(&cqspi->transfer_complete,
>> + msecs_to_jiffies(CQSPI_TIMEOUT_MS))) {
>> + dev_err(&pdev->dev, "Indirect write timeout\n");
>> + ret = -ETIMEDOUT;
>> + goto failwr;
>> + }
>> + remaining -= write_bytes;
>> + if (remaining < 0)
>> + reinit_completion(&cqspi->transfer_complete);
>> + }
>> +
>> + /* Check indirect done status */
>> + ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTWR,
>> + CQSPI_REG_INDIRECTWR_DONE_MASK, 0);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Indirect write completion error.\n");
>> + goto failwr;
>> + }
>> +
>> + return 0;
>> +
>> +failwr:
>> + /* Disable interrupt. */
>> + writel(0, reg_base + CQSPI_REG_IRQMASK);
>> + /* Clear indirect completion status */
>> + writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR);
>> +
>> + /* Cancel the indirect write */
>> + if (ret)
>> + writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
>> + reg_base + CQSPI_REG_INDIRECTWR);
>> +
>> + return ret;
>> +}
>> +
>> +void cqspi_controller_init(struct struct_cqspi *cqspi)
>> +{
>> + struct platform_device *pdev = cqspi->pdev;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +
>> + cqspi_controller_enable(cqspi->iobase, 0);
>> +
>> + /* Configure the remap address register, no remap */
>> + writel(0, cqspi->iobase + CQSPI_REG_REMAP);
>> +
>> + /* Disable all interrupts. */
>> + writel(0, cqspi->iobase + CQSPI_REG_IRQMASK);
>> +
>> + /* Load indirect trigger address. */
>> + writel(pdata->trigger_address,
>> + cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER);
>> +
>> + /* Enable Direct Access Controller */
>> + if (cqspi->use_dac_mode)
>> + cqspi_direct_access_enable(cqspi, 1);
>> +
>> + cqspi_controller_enable(cqspi->iobase, 1);
>> +}
>> +
>> +unsigned int calculate_ticks_for_ns(u32 ref_clk_hz, u32 ns_val)
> Prefix cqspi_ and make the function static
Noted, will fix it.
>> +{
>> + unsigned int ticks;
>> +
>> + ticks = ref_clk_hz / 1000; /* kHz */
>> + ticks = DIV_ROUND_UP(ticks * ns_val, 1000000);
>> +
>> + return ticks;
>> +}
>> +
>> +void cqspi_delay(struct struct_cqspi *cqspi, u32 ref_clk, u32 sclk_hz)
> static?
Noted, will fixt it.
>> +{
>> + struct platform_device *pdev = cqspi->pdev;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> + struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cqspi->current_cs];
>> + void __iomem *iobase = cqspi->iobase;
>> + const unsigned int ref_clk_hz = pdata->master_ref_clk_hz;
>> + unsigned int tchsh, tshsl, tslch, tsd2d;
>> + unsigned int reg;
>> + unsigned int tsclk;
>> +
>> + cqspi_controller_enable(cqspi->iobase, 0);
>> + /* calculate the number of ref ticks for one sclk tick */
>> + tsclk = DIV_ROUND_UP(ref_clk_hz, sclk_hz);
>> +
>> + /* The controller adds additional delay to that programmed in the reg */
>> + if (f_pdata->tshsl_ns < tsclk)
>> + tshsl = tsclk;
>> +
>> + tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns);
>> + tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns);
>> + tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns);
>> + tshsl = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tshsl_ns);
>> +
>> + reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
>> + << CQSPI_REG_DELAY_TSHSL_LSB);
>> + reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
>> + << CQSPI_REG_DELAY_TCHSH_LSB);
>> + reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
>> + << CQSPI_REG_DELAY_TSLCH_LSB);
>> + reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
>> + << CQSPI_REG_DELAY_TSD2D_LSB);
>> + writel(reg, iobase + CQSPI_REG_DELAY);
>> + cqspi_controller_enable(cqspi->iobase, 1);
>> +}
>> +
>> +void cqspi_switch_chipselect(struct struct_cqspi *cqspi, u32 cs)
> static?
Noted, will fixt it.
>> +{
>> + struct platform_device *pdev = cqspi->pdev;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> + struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cs];
>> + void __iomem *iobase = cqspi->iobase;
>> + unsigned int reg;
>> +
>> + cqspi_controller_enable(cqspi->iobase, 0);
>> + /* Configure page size and block size. */
>> + reg = readl(iobase + CQSPI_REG_SIZE);
>> + /* clear the previous value */
>> + reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
>> + reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
>> + reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
>> + reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
>> + writel(reg, iobase + CQSPI_REG_SIZE);
>> + /* configure the chip select */
>> + cqspi_chip_select(iobase, cs, pdata->ext_decoder);
>> + cqspi_controller_enable(cqspi->iobase, 1);
>> +}
>> +
>> +static int cqspi_apb_read_execute(struct struct_cqspi *cqspi,
>> + const struct spi_mem_op *op, u8 *rxbuf)
>> +{
>> + u32 from = op->addr.val;
>> + void *buf = op->data.buf.in;
>> + size_t len = op->data.nbytes;
>> +
>> + if (cqspi->use_dac_mode && (from + len < cqspi->ahb_size)) {
>> + memcpy_fromio(buf, cqspi->ahbbase + from, len);
> Hmm, You have dropped DMA support... This will be a regression :(
sorry , dont have the setup so understood the code , accordingly changed .
>> + if (!cqspi_wait_idle(cqspi))
>> + return -EIO;
>> + return 0;
>> + }
>> +
>> + return cqspi_indirect_read_execute(cqspi, op, rxbuf);
>> +}
>> +
>> +int cqspi_apb_write_execute(struct struct_cqspi *cqspi,
>> + const struct spi_mem_op *op, const u8 *txbuf)
> static? Please make all functions static if they are local to the module.
Noted, will fixt it.
>> +{
>> + u32 to = op->addr.val;
>> + const void *buf = op->data.buf.out;
>> + size_t len = op->data.nbytes;
>> +
>> + if (cqspi->use_dac_mode && (to + len < cqspi->ahb_size)) {
>> + memcpy_toio(cqspi->ahbbase + to, buf, len);
>> + if (!cqspi_wait_idle(cqspi))
>> + return -EIO;
>> + return 0;
>> + }
>> +
>> + return cqspi_indirect_write_execute(cqspi, op, txbuf);
>> +}
>> +
>> +static int cqspi_mem_process(struct struct_cqspi *cqspi, struct spi_mem *mem,
>> + const struct spi_mem_op *op)
>> +{
>> + struct platform_device *pdev = cqspi->pdev;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> + unsigned int tmpbufsize, n_trans = 0, totalxferlen = 0;
>> + void __iomem *iobase = cqspi->iobase;
>> + struct spi_mem_op_cadence ops[4] = { };
>> + struct spi_mem_op_cadence *cmd_ops = NULL;
>> + struct spi_mem_op_cadence *data_ops = NULL;
>> + struct spi_mem_op_cadence *dummy_ops = NULL;
>> + struct spi_mem_op_cadence *addr_ops = NULL;
>> + struct cqspi_flash_pdata *f_pdata;
>> + int mode, err, i;
>> + u8 *tmpbuf;
>> + u32 sclk;
>> +
>> + if (cqspi->current_cs != mem->spi->chip_select) {
>> + cqspi->current_cs = mem->spi->chip_select;
>> + cqspi_switch_chipselect(cqspi, mem->spi->chip_select);
>> + }
>> +
>> + f_pdata = &pdata->f_pdata[cqspi->current_cs];
>> +
>> + tmpbufsize = sizeof(op->cmd.opcode) + op->addr.nbytes +
>> + op->dummy.nbytes;
>> +
>> + tmpbuf = kzalloc(tmpbufsize, GFP_KERNEL | GFP_DMA);
> I don't understand the need for this buffer and spi_mem_op_cadence..
> Since, struct spi_mem_op is anyways passed at all places where
> cmd/data/addr_ops are being used. I think its possible to drop them...
> See below
while testing crash happened that's the reason , kept it.
>> + if (!tmpbuf)
>> + return -ENOMEM;
>> +
>> + tmpbuf[0] = op->cmd.opcode;
>> + ops[n_trans].tx_buf = tmpbuf;
>> + ops[n_trans].len = sizeof(op->cmd.opcode);
>> + ops[n_trans].tx_nbits = op->cmd.buswidth;
>> +
>> + n_trans++;
>> + totalxferlen++;
>> +
>> + if (op->addr.nbytes) {
>> + int i;
>> +
>> + for (i = 0; i < op->addr.nbytes; i++)
>> + tmpbuf[i + 1] = op->addr.val >>
>> + (8 * (op->addr.nbytes - i - 1));
>> +
> cqspi_cmd2addr()?

Address alignment for data (read/write) operation in user area, mainly
kept this to avoid functionality breakage,

checked other drivers as well which you have referred, same thing they
are also doing for aligment of data access.

>> + ops[n_trans].tx_buf = tmpbuf + 1;
>> + ops[n_trans].len = op->addr.nbytes;
>> + ops[n_trans].tx_nbits = op->addr.buswidth;
>> +
>> + n_trans++;
>> + totalxferlen += op->addr.nbytes;
>> + }
>> + if (op->dummy.nbytes) {
>> + memset(tmpbuf + op->addr.nbytes + 1, 0xff, op->dummy.nbytes);
>> + ops[n_trans].tx_buf = tmpbuf + op->addr.nbytes + 1;
>> + ops[n_trans].len = op->dummy.nbytes;
>> + ops[n_trans].tx_nbits = op->dummy.buswidth;
>> +
>> + n_trans++;
>> + totalxferlen += op->dummy.nbytes;
>> + }
>> + if (op->data.nbytes) {
>> + if (op->data.dir == SPI_MEM_DATA_IN) {
>> + ops[n_trans].rx_buf = op->data.buf.in;
>> + ops[n_trans].rx_nbits = op->data.buswidth;
>> + } else {
>> + ops[n_trans].tx_buf = op->data.buf.out;
>> + ops[n_trans].tx_nbits = op->data.buswidth;
>> + }
>> +
>> + ops[n_trans].len = op->data.nbytes;
>> + n_trans++;
>> + totalxferlen += op->data.nbytes;
>> + }
>> +
>> + for (i = 0; i < n_trans; i++)
>> + dev_dbg(&pdev->dev, "ops[%d] %d\n", i, ops[i].len);
>> +
>> + switch (n_trans) {
>> + case 1:
>> + cmd_ops = &ops[0];
> I don't see any cmd_ops being consumed anywhere. So clearly this can be
> dropped,
Noted, will fixt it.
>> + break;
>> + case 2:
>> + cmd_ops = &ops[0];
>> + data_ops = &ops[1];
>> + break;
>> + case 3:
>> + cmd_ops = &ops[0];
>> + addr_ops = &ops[1];
>> + data_ops = &ops[2];
>> + break;
>> + case 4:
>> + cmd_ops = &ops[0];
>> + addr_ops = &ops[1];
>> + dummy_ops = &ops[2];
>> + data_ops = &ops[3];
>> + break;
>> + default:
>> + dev_err(&pdev->dev, "Unsupported n_trans %u\n", n_trans);
>> + return -EINVAL;
>> + }
>> + if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) {
>> + if (!op->addr.nbytes)
>> + mode = CQSPI_STIG_READ;
>> + else
>> + mode = CQSPI_INDIRECT_READ;
> Drop INDIRECT in the name... Driver supports both the modes.
Noted, will fixt it.
>> + } else {
>> + if (!op->addr.nbytes || !op->data.buf.out)
>> + mode = CQSPI_STIG_WRITE;
>> + else
>> + mode = CQSPI_INDIRECT_WRITE;
> Same here...
Noted, will fixt it.
>> + }
>> +
>> + sclk = mem->spi->max_speed_hz;
>> + cqspi_controller_enable(iobase, 0);
>> + cqspi_config_baudrate_div(iobase, pdata->master_ref_clk_hz, sclk);
>> + cqspi_delay(cqspi, pdata->master_ref_clk_hz, sclk);
>> + cqspi_readdata_capture(iobase, 1, f_pdata->read_delay);
>> + cqspi_controller_enable(iobase, 1);
>> +
>> + /* execute transfer */
>> + switch (mode) {
>> + case CQSPI_STIG_WRITE:
>> + err = cqspi_command_write(cqspi, op);
>> + if (err) {
>> + dev_err(&pdev->dev, "QSPI: Command Write failed!.\n");
>> + return err;
>> + }
>> + break;
>> + case CQSPI_STIG_READ:
>> + err = cqspi_command_read(cqspi, op);
>> + if (err) {
>> + dev_err(&pdev->dev, "QSPI: Command Read failed!.\n");
>> + return err;
>> + }
>> + break;
>> + case CQSPI_INDIRECT_WRITE:
>> + err = cqspi_indirect_write_setup(cqspi, op, addr_ops->tx_buf);
> No need for addr_ops, just move the logic associated with it into above
> function.
> Also rename above function to drop reference to indirect mode
Noted, will fixt it.
>> + err = cqspi_apb_write_execute(cqspi, op, data_ops->tx_buf);
>
> Instead of data_ops, why not just use op->data.buf.out inside
> cqspi_apb_write_execute()?
Noted, will fixt it.
>> + if (err) {
>> + dev_err(&pdev->dev, "QSPI: Write Execution failed!.\n");
>> + return err;
>> + }
>> + break;
>> + case CQSPI_INDIRECT_READ:
>> + err = cqspi_indirect_read_setup(cqspi, op, addr_ops->tx_buf);
> Same as above
>
>> + err = cqspi_apb_read_execute(cqspi, op, data_ops->rx_buf);
> Instead of data_ops, why not just use op->data.buf.in inside
> cqspi_apb_read_execute()?
>
>> + if (err) {
>> + dev_err(&pdev->dev, "QSPI: Read Execution failed!.\n");
>> + return err;
>> + }
>> + break;
>> + default:
>> + dev_err(&pdev->dev, "Unsupported mode %u\n", mode);
>> + return -EINVAL;
>> + }
>> +
>> + return err;
>> +}
>> +
>> +int cqspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
>> +{
>> + struct struct_cqspi *cqspi = spi_master_get_devdata(mem->spi->master);
>> + int ret;
>> +
>> + mutex_lock(&cqspi->lock);
>> + ret = cqspi_mem_process(cqspi, mem, op);
>> + if (ret)
>> + dev_err(&mem->spi->dev, "QSPI: qspi transfer failed!!!.\n");
>> + mutex_unlock(&cqspi->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct spi_controller_mem_ops cqspi_mem_ops = {
>> + .exec_op = cqspi_exec_mem_op,
>> +};
>> +
>> +static int cqspi_setup(struct spi_device *spi)
>> +{
>> + if (spi->chip_select > spi->master->num_chipselect) {
>> + dev_err(&spi->dev, "QSPI: chip_select is out of range\n");
>> + return -EINVAL;
>> + }
> This is where driver should setup flash_pdata (i.e call
> cqspi_of_get_flash_pdata() here)
>
Noted, will fixt it.
>
>> + return 0;
>> +}
>> +
>> +static int cqspi_of_get_flash_pdata(struct platform_device *pdev)
>> +{
>> + struct device_node *np = pdev->dev.of_node;
>> + struct device_node *nc;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> + struct cqspi_flash_pdata *f_pdata;
>> + u32 prop, cs;
>> +
>> + /* Get flash devices platform data */
>> + for_each_child_of_node(np, nc) {
>> + if (!of_device_is_available(nc))
>> + continue;
>> +
>> + if (of_property_read_u32(nc, "reg", &cs)) {
>> + dev_err(&pdev->dev, "couldn't determine reg\n");
>> + return -ENXIO;
>> + }
>> + f_pdata = &pdata->f_pdata[cs];
>> +
>> + if (of_property_read_u32(nc, "cdns,read-delay", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine read-delay\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->read_delay = prop;
>> +
>> + if (of_property_read_u32(nc, "cdns,tshsl-ns", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine tshsl-ns\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->tshsl_ns = prop;
>> +
>> + if (of_property_read_u32(nc, "cdns,tsd2d-ns", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine tsd2d-ns\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->tsd2d_ns = prop;
>> +
>> + if (of_property_read_u32(nc, "cdns,tchsh-ns", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine tchsh-ns\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->tchsh_ns = prop;
>> +
>> + if (of_property_read_u32(nc, "cdns,tslch-ns", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine tslch-ns\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->tslch_ns = prop;
>> +
>> + if (of_property_read_u32(nc, "page-size", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine page-size\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->page_size = prop;
>> +
>> + if (of_property_read_u32(nc, "block-size", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine block-size\n");
>> + return -ENXIO;
>> + }
>> + f_pdata->block_size = prop;
>> + }
>> + return 0;
>> +}
>> +
>> +static int cqspi_of_get_pdata(struct platform_device *pdev)
>> +{
>> + struct device_node *np = pdev->dev.of_node;
>> + struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> + unsigned int prop;
>> + int ret;
>> +
>> + pdata->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs");
>> +
>> + if (of_property_read_u32(np, "cdns,fifo-depth", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine fifo-depth\n");
>> + return -ENXIO;
>> + }
>> + pdata->fifo_depth = prop;
>> +
>> + if (of_property_read_u32(np, "cdns,fifo-width", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine fifo-width\n");
>> + return -ENXIO;
>> + }
>> + pdata->fifo_width = prop;
>> +
>> + if (of_property_read_u32(np, "cdns,trigger-address", &prop)) {
>> + dev_err(&pdev->dev, "couldn't determine trigger-address\n");
>> + return -ENXIO;
>> + }
>> + pdata->trigger_address = prop;
>> +
>> + pdata->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
>> +
>> + ret = cqspi_of_get_flash_pdata(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Get flash data failed.\n");
>> + return -ENODEV;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cqspi_probe(struct platform_device *pdev)
>> +{
>> + struct cqspi_platform_data *pdata;
>> + struct device *dev = &pdev->dev;
>> + struct struct_cqspi *cqspi;
>> + struct spi_master *master;
>> + struct reset_control *rstc, *rstc_ocp;
>> + const struct cqspi_driver_platdata *ddata;
>> + struct resource *res = NULL;
>> + int ret;
>> +
>> + master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
>> + if (!master) {
>> + dev_err(&pdev->dev, "spi_alloc_master failed\n");
>> + return -ENOMEM;
>> + }
>> + master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA | SPI_TX_QUAD |
>> + SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL |
>> + SPI_TX_OCTAL | SPI_RX_OCTAL;
> Driver does not support Multi IO TX, so lets drop SPI_TX_DUAL,
> SPI_TX_QUAD and SPI_TX_OCTAL for now. No support for changing polarity,
> phase or inverted CS (although IP may support these) either... So this
> should be
>
> master->mode_bits = SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL | SPI_RX_OCTAL;
Noted, will fixt it.
>> + master->setup = cqspi_setup;
>> + master->mem_ops = &cqspi_mem_ops;
>> + master->dev.of_node = pdev->dev.of_node;
>> + cqspi = spi_master_get_devdata(master);
>> + cqspi->pdev = pdev;
>> +
>> + pdata = kmalloc(sizeof(*pdata), GFP_KERNEL);
> Use devm_kmalloc()
Noted, will fixt it.
>> + if (!pdata) {
>> + ret = -ENOMEM;
>> + goto err_pdata;
>> + }
>> + pdev->dev.platform_data = pdata;
>> +
>> + /* Obtain QSPI clock. */
>> + cqspi->clk = devm_clk_get(&pdev->dev, "qspi");
>> + if (IS_ERR(cqspi->clk)) {
>> + dev_err(&pdev->dev, "cannot get qspi clk\n");
>> + return PTR_ERR(cqspi->clk);
>> + }
>> + pdata->master_ref_clk_hz = clk_get_rate(cqspi->clk);
>> +
>> + ret = clk_prepare_enable(cqspi->clk);
>> + if (ret < 0) {
>> + dev_err(&pdev->dev, "failed to enable qspi clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + /* Obtain configuration from OF. */
>> + ret = cqspi_of_get_pdata(pdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Get platform data failed.\n");
>> + return -ENODEV;
>> + }
>> +
>> + cqspi->res = res;
>> + /* Obtain and remap controller address. */
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + cqspi->iobase = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(cqspi->iobase)) {
>> + dev_err(dev, "Cannot remap controller address.\n");
>> + return PTR_ERR(cqspi->iobase);
>> + }
>> +
>> + /* Obtain and remap AHB address. */
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>> + cqspi->qspi_ahb_virt = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(cqspi->qspi_ahb_virt)) {
>> + dev_err(dev, "Cannot remap AHB address.\n");
>> + return PTR_ERR(cqspi->qspi_ahb_virt);
>> + }
>> + cqspi->ahbbase = res;
>> + cqspi->ahb_size = resource_size(res);
>> +
>> + /* Obtain QSPI reset control */
>> + rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
>> + if (IS_ERR(rstc)) {
>> + dev_err(dev, "Cannot get QSPI reset.\n");
>> + return PTR_ERR(rstc);
>> + }
>> +
>> + rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
>> + if (IS_ERR(rstc_ocp)) {
>> + dev_err(dev, "Cannot get QSPI OCP reset.\n");
>> + return PTR_ERR(rstc_ocp);
>> + }
>> +
>> + reset_control_assert(rstc);
>> + reset_control_deassert(rstc);
>> +
>> + reset_control_assert(rstc_ocp);
>> + reset_control_deassert(rstc_ocp);
>> +
>> + ddata = of_device_get_match_data(dev);
>> + if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
>> + cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
>> + pdata->master_ref_clk_hz);
>> +
>> + if (ddata && (ddata->quirks & CQSPI_DISABLE_DAC_MODE))
>> + cqspi->use_dac_mode = false;
>> +
>> + init_completion(&cqspi->transfer_complete);
>> +
>> + /* Obtain IRQ line. */
>> + cqspi->irq = platform_get_irq(pdev, 0);
>> + if (cqspi->irq < 0) {
>> + dev_err(dev, "platform_get_irq failed.\n");
>> + ret = -ENXIO;
>> + goto err_irq;
>> + }
>> + ret = devm_request_irq(dev, cqspi->irq, cqspi_irq_handler, 0,
>> + pdev->name, cqspi);
>> + if (ret) {
>> + dev_err(dev, "request_irq failed.\n");
>> + goto err_irq;
>> + }
>> +
>> + master->bus_num = pdata->bus_num;
>> + master->num_chipselect = pdata->num_chipselect;
>> + mutex_init(&cqspi->lock);
>> + platform_set_drvdata(pdev, master);
>> + cqspi_controller_init(cqspi);
>> + cqspi->current_cs = -1;
>> +
>> + ret = devm_spi_register_master(dev, master);
>> + if (ret) {
>> + dev_err(&pdev->dev, "devm_spi_register_master failed.\n");
>> + goto err_of;
>> + }
>> +
>> + return 0;
>> +
>> +err_pdata:
>> + kfree(pdata);
> Can be dropped if pdata is devm_kmalloc'd
Noted, will fixt it.
>> +err_irq:
>> + free_irq(cqspi->irq, cqspi);
> No need to free explicitly.... IRQ was requested as devm_request_irq()
Noted, will remove it.
>> +err_of:
>> + spi_master_put(master);
>> + dev_err(&pdev->dev, "Cadence QSPI controller probe failed\n");
>> + return ret;
>> +}
>> +
>> +static int cqspi_remove(struct platform_device *pdev)
>> +{
>> + struct spi_master *master = platform_get_drvdata(pdev);
>> + struct struct_cqspi *cadence_qspi = spi_master_get_devdata(master);
>> +
>> + cqspi_controller_enable(cadence_qspi->iobase, 0);
>
>> + platform_set_drvdata(pdev, NULL);
>> + free_irq(cadence_qspi->irq, cadence_qspi);
>> + iounmap(cadence_qspi->iobase);
>> + iounmap(cadence_qspi->qspi_ahb_virt);
>> + release_mem_region(cadence_qspi->res->start,
>> + resource_size(cadence_qspi->res));
>> + kfree(pdev->dev.platform_data);
>> + spi_unregister_master(master);
>> + spi_master_put(master);
> No need for any of these... Since, these resources are allocated (or
> registered) using devm_* APIs, they are freed automatically on remove.
>
Agreed!!
>> + return 0;
>> +}
>> +
>> +static const struct cqspi_driver_platdata k2g_qspi = {
>> + .quirks = CQSPI_NEEDS_WR_DELAY,
>> +};
>> +
>> +static const struct cqspi_driver_platdata am654_ospi = {
>> + .quirks = CQSPI_NEEDS_WR_DELAY,
>> +};
>> +
>> +static const struct cqspi_driver_platdata intel_lgm_qspi = {
>> + .quirks = CQSPI_DISABLE_DAC_MODE,
>> +};
>> +
>> +#ifdef CONFIG_OF
>> +static const struct of_device_id cqspi_of_match[] = {
>> + {
>> + .compatible = "cadence,qspi",
>> + },
>> + {
>> + .compatible = "ti,k2g-qspi",
>> + .data = &k2g_qspi,
>> + },
>> + {
>> + .compatible = "ti,am654-ospi",
>> + .data = &am654_ospi,
>> + },
>> + {
>> + .compatible = "intel,lgm-qspi",
>> + .data = &intel_lgm_qspi,
>> + },
>> + { /* end of table */}
>> +};
>> +MODULE_DEVICE_TABLE(of, cqspi_of_match);
>> +#else
>> +#define cqspi_of_match NULL
>> +#endif /* CONFIG_OF */
>> +
>> +static struct platform_driver cqspi_platform_driver = {
>> + .probe = cqspi_probe,
>> + .remove = cqspi_remove,
>> + .driver = {
>> + .name = CADENCE_QSPI_NAME,
>> + .of_match_table = cqspi_of_match,
>> + },
>> +};
>> +
>> +module_platform_driver(cqspi_platform_driver);
>> +
>> +MODULE_DESCRIPTION("Cadence QSPI Controller Driver");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_ALIAS("platform:" CADENCE_QSPI_NAME);
>> +MODULE_AUTHOR("Ley Foon Tan <lftan@altera.com>");
>> +MODULE_AUTHOR("Graham Moore <grmoore@opensource.altera.com>");
>> +MODULE_AUTHOR("Vadivel Murugan R <vadivel.muruganx.ramuthevar@intel.com>");
>> diff --git a/drivers/spi/spi-cadence-quadspi.h b/drivers/spi/spi-cadence-quadspi.h
>> new file mode 100644
>> index 000000000000..e306b30e4d03
>> --- /dev/null
>> +++ b/drivers/spi/spi-cadence-quadspi.h
>> @@ -0,0 +1,251 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +/*
>> + * Driver for Cadence QSPI Controller
>> + *
>> + * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
>> + * Copyright Intel Corporation (C) 2019-2020. All rights reserved.
>> + */
>> +#ifndef __CADENCE_QSPI__H__
>> +#define __CADENCE_QSPI__H__
>> +#include <linux/reset.h>
>> +#include <linux/spi/spi-mem.h>
>> +
>> +#define CQSPI_MAX_CHIP_SELECT (16)
>> +#define CQSPI_STIG_READ 1
>> +#define CQSPI_STIG_WRITE 2
>> +#define CQSPI_INDIRECT_READ 3
>> +#define CQSPI_INDIRECT_WRITE 4
>> +
>> +#define QUAD_SIO 0
>> +#define QUAD_DIO 1
>> +#define QUAD_QIO 2
>> +
>> +#define QUAD_LSB 4
>> +
> Drop unused constants, please... I don't see a need to add any more
> constants than whats already present in old driver...
Noted, will fixt it.
>> +/* Operation timeout value */
>> +#define CQSPI_TIMEOUT_MS 5000
>> +#define CQSPI_READ_TIMEOUT_MS 10
>> +#define CQSPI_POLL_IDLE_RETRY 3
>> +#define CQSPI_FIFO_WIDTH 4
>> +
>> +/* Controller sram size in word */
>> +#define CQSPI_REG_SRAM_RESV_WORDS 2
>> +#define CQSPI_REG_SRAM_PARTITION_WR 1
>> +#define CQSPI_REG_SRAM_THRESHOLD_BYTES 50
>> +
>> +/* Instruction type */
>> +#define CQSPI_INST_TYPE_SINGLE 0
>> +#define CQSPI_INST_TYPE_DUAL 1
>> +#define CQSPI_INST_TYPE_QUAD 2
>> +#define CQSPI_DUMMY_CLKS_PER_BYTE 8
>> +#define CQSPI_DUMMY_BYTES_MAX 4
>> +#define CQSPI_STIG_DATA_LEN_MAX 8
>> +#define CQSPI_INDIRECTTRIGGER_ADDR_MASK 0xFFFFF
>> +
>> +/* Register map */
>> +#define CQSPI_REG_CONFIG 0x00
>> +#define CQSPI_REG_CONFIG_ENABLE_MASK BIT(0)
>> +#define CQSPI_REG_CONFIG_DIRECT_MASK BIT(7)
>> +#define CQSPI_REG_CONFIG_DECODE_MASK BIT(9)
>> +#define CQSPI_REG_CONFIG_CHIPSELECT_LSB 10
>> +#define CQSPI_REG_CONFIG_DMA_MASK BIT(15)
>> +#define CQSPI_REG_CONFIG_BAUD_LSB 19
>> +#define CQSPI_REG_CONFIG_IDLE_LSB 31
>> +#define CQSPI_REG_CONFIG_CHIPSELECT_MASK 0xF
>> +#define CQSPI_REG_CONFIG_BAUD_MASK 0xF
>> +#define CQSPI_REG_RD_INSTR 0x04
>> +#define CQSPI_REG_RD_INSTR_OPCODE_LSB 0
>> +#define CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB 8
>> +#define CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB 12
>> +#define CQSPI_REG_RD_INSTR_TYPE_DATA_LSB 16
>> +#define CQSPI_REG_RD_INSTR_MODE_EN_LSB 20
>> +#define CQSPI_REG_RD_INSTR_DUMMY_LSB 24
>> +#define CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK 0x3
>> +#define CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK 0x3
>> +#define CQSPI_REG_RD_INSTR_TYPE_DATA_MASK 0x3
>> +#define CQSPI_REG_RD_INSTR_DUMMY_MASK 0x1F
>> +#define CQSPI_REG_WR_INSTR 0x08
>> +#define CQSPI_REG_WR_INSTR_OPCODE_LSB 0
>> +#define CQSPI_REG_WR_INSTR_TYPE_DATA_MASK 0x3
>> +#define CQSPI_REG_WR_INSTR_TYPE_DATA_LSB 16
>> +#define CQSPI_REG_WR_INSTR_TYPE_ADDR_MASK 0x3
>> +#define CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB 12
>> +
>> +/*! Field WEL_DIS_FLD - wel_dis_fld */
>> +#define CQSPI_REG_WR_CONFIG_WEL_DIS_FLD_POS 8
>> +#define CQSPI_REG_WR_COMPLETION_CTRL 0x38
>> +#define CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS 14
>> +
>> +#define CQSPI_REG_DELAY 0x0C
>> +#define CQSPI_REG_DELAY_TSLCH_LSB 0
>> +#define CQSPI_REG_DELAY_TCHSH_LSB 8
>> +#define CQSPI_REG_DELAY_TSD2D_LSB 16
>> +#define CQSPI_REG_DELAY_TSHSL_LSB 24
>> +#define CQSPI_REG_DELAY_TSLCH_MASK 0xFF
>> +#define CQSPI_REG_DELAY_TCHSH_MASK 0xFF
>> +#define CQSPI_REG_DELAY_TSD2D_MASK 0xFF
>> +#define CQSPI_REG_DELAY_TSHSL_MASK 0xFF
>> +#define CQSPI_REG_READCAPTURE 0x10
>> +#define CQSPI_REG_READCAPTURE_BYPASS_LSB 0
>> +#define CQSPI_REG_READCAPTURE_DELAY_LSB 1
>> +#define CQSPI_REG_READCAPTURE_DELAY_MASK 0xF
>> +#define CQSPI_REG_SIZE 0x14
>> +#define CQSPI_REG_SIZE_ADDRESS_LSB 0
>> +#define CQSPI_REG_SIZE_PAGE_LSB 4
>> +#define CQSPI_REG_SIZE_BLOCK_LSB 16
>> +#define CQSPI_REG_SIZE_ADDRESS_MASK 0xF
>> +#define CQSPI_REG_SIZE_PAGE_MASK 0xFFF
>> +#define CQSPI_REG_SIZE_BLOCK_MASK 0x3F
>> +#define CQSPI_REG_SRAMPARTITION 0x18
>> +#define CQSPI_REG_INDIRECTTRIGGER 0x1C
>> +#define CQSPI_REG_DMA 0x20
>> +#define CQSPI_REG_DMA_SINGLE_LSB 0
>> +#define CQSPI_REG_DMA_BURST_LSB 8
>> +#define CQSPI_REG_DMA_SINGLE_MASK 0xFF
>> +#define CQSPI_REG_DMA_BURST_MASK 0xFF
>> +#define CQSPI_REG_REMAP 0x24
>> +#define CQSPI_REG_MODE_BIT 0x28
>> +#define CQSPI_REG_SDRAMLEVEL 0x2C
>> +#define CQSPI_REG_SDRAMLEVEL_RD_LSB 0
>> +#define CQSPI_REG_SDRAMLEVEL_WR_LSB 16
>> +#define CQSPI_REG_SDRAMLEVEL_RD_MASK 0xFFFF
>> +#define CQSPI_REG_SDRAMLEVEL_WR_MASK 0xFFFF
>> +
>> +#define CQSPI_REG_IRQSTATUS 0x40
>> +#define CQSPI_REG_IRQMASK 0x44
>> +#define CQSPI_REG_INDIRECTRD 0x60
>> +#define CQSPI_REG_INDIRECTRD_START_MASK BIT(0)
>> +#define CQSPI_REG_INDIRECTRD_CANCEL_MASK BIT(1)
>> +#define CQSPI_REG_INDIRECTRD_DONE_MASK BIT(5)
>> +#define CQSPI_REG_INDIRECTRDWATERMARK 0x64
>> +#define CQSPI_REG_INDIRECTRDSTARTADDR 0x68
>> +#define CQSPI_REG_INDIRECTRDBYTES 0x6C
>> +#define CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG 0x80
>> +#define CQSPI_REG_CMDCTRL 0x90
>> +#define CQSPI_REG_CMDCTRL_EXECUTE_MASK BIT(0)
>> +#define CQSPI_REG_CMDCTRL_INPROGRESS_MASK BIT(1)
>> +#define CQSPI_REG_CMDCTRL_WR_BYTES_LSB 12
>> +#define CQSPI_REG_CMDCTRL_WR_EN_LSB 15
>> +#define CQSPI_REG_CMDCTRL_ADD_BYTES_LSB 16
>> +#define CQSPI_REG_CMDCTRL_ADDR_EN_LSB 19
>> +#define CQSPI_REG_CMDCTRL_RD_BYTES_LSB 20
>> +#define CQSPI_REG_CMDCTRL_RD_EN_LSB 23
>> +#define CQSPI_REG_CMDCTRL_OPCODE_LSB 24
>> +#define CQSPI_REG_CMDCTRL_WR_BYTES_MASK 0x7
>> +#define CQSPI_REG_CMDCTRL_ADD_BYTES_MASK 0x3
>> +#define CQSPI_REG_CMDCTRL_RD_BYTES_MASK 0x7
>> +#define CQSPI_REG_INDIRECTWR 0x70
>> +#define CQSPI_REG_INDIRECTWR_START_MASK BIT(0)
>> +#define CQSPI_REG_INDIRECTWR_CANCEL_MASK BIT(1)
>> +#define CQSPI_REG_INDIRECTWR_DONE_MASK BIT(5)
>> +#define CQSPI_REG_INDIRECTWRWATERMARK 0x74
>> +#define CQSPI_REG_INDIRECTWRSTARTADDR 0x78
>> +#define CQSPI_REG_INDIRECTWRBYTES 0x7C
>> +#define CQSPI_REG_CMDADDRESS 0x94
>> +#define CQSPI_REG_CMDREADDATALOWER 0xA0
>> +#define CQSPI_REG_CMDREADDATAUPPER 0xA4
>> +#define CQSPI_REG_CMDWRITEDATALOWER 0xA8
>> +#define CQSPI_REG_CMDWRITEDATAUPPER 0xAC
>> +
>> +/* Interrupt status bits */
>> +#define CQSPI_REG_IRQ_MODE_ERR BIT(0)
>> +#define CQSPI_REG_IRQ_UNDERFLOW BIT(1)
>> +#define CQSPI_REG_IRQ_IND_COMP BIT(2)
>> +#define CQSPI_REG_IRQ_IND_RD_REJECT BIT(3)
>> +#define CQSPI_REG_IRQ_WR_PROTECTED_ERR BIT(4)
>> +#define CQSPI_REG_IRQ_ILLEGAL_AHB_ERR BIT(5)
>> +#define CQSPI_REG_IRQ_WATERMARK BIT(6)
>> +#define CQSPI_REG_IRQ_IND_RD_OVERFLOW BIT(12)
>> +#define CQSPI_IRQ_STATUS_ERR (CQSPI_REG_IRQ_MODE_ERR | \
>> + CQSPI_REG_IRQ_IND_RD_REJECT | \
>> + CQSPI_REG_IRQ_WR_PROTECTED_ERR | \
>> + CQSPI_REG_IRQ_ILLEGAL_AHB_ERR)
>> +#define CQSPI_IRQ_MASK_RD (CQSPI_REG_IRQ_MODE_ERR | \
>> + CQSPI_REG_IRQ_IND_RD_REJECT | \
>> + CQSPI_REG_IRQ_WATERMARK | \
>> + CQSPI_REG_IRQ_IND_RD_OVERFLOW | \
>> + CQSPI_REG_IRQ_IND_COMP)
>> +#define CQSPI_IRQ_MASK_WR (CQSPI_REG_IRQ_MODE_ERR | \
>> + CQSPI_REG_IRQ_WR_PROTECTED_ERR | \
>> + CQSPI_REG_IRQ_IND_COMP | \
>> + CQSPI_REG_IRQ_WATERMARK | \
>> + CQSPI_REG_IRQ_UNDERFLOW)
>> +
>> +#define CQSPI_IRQ_STATUS_MASK (0xFFFFFFFF)
>> +#define CQSPI_CAL_DELAY(tdelay_ns, tref_ns, tsclk_ns) \
>> + ((((tdelay_ns) - (tsclk_ns)) / (tref_ns)))
>> +#define CQSPI_GET_RD_SRAM_LEVEL(reg_basse) \
>> + (((readl(reg_base + CQSPI_REG_SDRAMLEVEL)) >> \
>> + CQSPI_REG_SDRAMLEVEL_RD_LSB) & CQSPI_REG_SDRAMLEVEL_RD_MASK)
>> +
>> +struct cqspi_flash_pdata {
>> + u32 page_size;
>> + u32 block_size;
>> + u32 flash_type;
>> + u32 quad;
>> + u32 read_delay;
>> + u32 tshsl_ns;
>> + u32 tsd2d_ns;
>> + u32 tchsh_ns;
>> + u32 tslch_ns;
>> +};
>> +
>> +struct cqspi_platform_data {
>> + u32 bus_num;
>> + u32 num_chipselect;
>> + u32 qspi_ahb_phy;
>> + u32 qspi_ahb_size;
>> + u32 qspi_ahb_mask;
>> + u32 master_ref_clk_hz;
>> + u32 ext_decoder;
>> + u32 fifo_depth;
>> + u32 fifo_width;
>> + u32 enable_dma;
>> + u32 tx_dma_peri_id;
>> + u32 rx_dma_peri_id;
>> + u32 trigger_address;
>> + bool is_decoded_cs;
>> + bool rclk_en;
>> + struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIP_SELECT];
>> +};
>> +
>> +struct struct_cqspi {
>> + struct platform_device *pdev;
>> +
>> + struct clk *clk;
>> + struct clk *fpi_clk;
>> +
>> + struct reset_control *reset;
>> + struct completion transfer_complete;
>> + struct workqueue_struct *workqueue;
>> + wait_queue_head_t waitqueue;
>> + /* mutex lock for synchronization */
>> + struct mutex lock;
>> +
>> + void __iomem *iobase;
>> + void __iomem *qspi_ahb_virt;
>> + struct resource *res;
>> + struct resource *ahbbase;
>> + resource_size_t ahb_size;
>> +
>> + struct dma_chan *rx_chan;
>> + struct completion rx_dma_complete;
>> + dma_addr_t mmap_phys_base;
>> + int dma_done;
>> + u32 trigger_address;
>> + u32 wr_delay;
>> + u32 irq_status;
>> + int current_cs;
>> + int irq;
>> + bool use_dac_mode;
>> +};
>> +
>> +struct spi_mem_op_cadence {
>> + const void *tx_buf;
>> + void *rx_buf;
>> + u32 len;
>> + u32 tx_nbits:3;
>> + u32 rx_nbits:3;
>> +};
>> +
>> +#endif /* __CADENCE_QSPI__H__ */
>>

\
 
 \ /
  Last update: 2019-12-17 06:55    [W:0.069 / U:0.488 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site