lkml.org 
[lkml]   [2019]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v7 7/7] arm64: dts: allwinner: a64: Add thermal sensors and thermal zones
Date
A64 has 3 thermal sensors: 1 for CPU, 2 for GPU.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 27e48234f1c2..e6556c6d7777 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -49,6 +49,7 @@
#include <dt-bindings/reset/sun50i-a64-ccu.h>
#include <dt-bindings/reset/sun8i-de2.h>
#include <dt-bindings/reset/sun8i-r-ccu.h>
+#include <dt-bindings/thermal/thermal.h>

/ {
interrupt-parent = <&gic>;
@@ -211,6 +212,29 @@ timer {
(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};

+ thermal-zones {
+ cpu_thermal: cpu0-thermal {
+ /* milliseconds */
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 0>;
+ };
+
+ gpu0_thermal: gpu0-thermal {
+ /* milliseconds */
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 1>;
+ };
+
+ gpu1_thermal: gpu1-thermal {
+ /* milliseconds */
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 2>;
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -485,6 +509,12 @@ mmc2: mmc@1c11000 {
sid: eeprom@1c14000 {
compatible = "allwinner,sun50i-a64-sid";
reg = <0x1c14000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ths_calibration: thermal-sensor-calibration@34 {
+ reg = <0x34 0x6>;
+ };
};

crypto: crypto@1c15000 {
@@ -810,6 +840,18 @@ codec: codec@1c22e00 {
status = "disabled";
};

+ ths: thermal-sensor@1c25000 {
+ compatible = "allwinner,sun50i-a64-ths";
+ reg = <0x01c25000 0x100>;
+ clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+ clock-names = "bus", "mod";
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&ccu RST_BUS_THS>;
+ nvmem-cells = <&ths_calibration>;
+ nvmem-cell-names = "calibration";
+ #thermal-sensor-cells = <1>;
+ };
+
uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
--
2.24.1
\
 
 \ /
  Last update: 2019-12-18 05:22    [W:0.070 / U:0.884 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site