lkml.org 
[lkml]   [2019]   [Dec]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 11/14] ARM: dts: sun8i: r40: Add device node for CSI0
On Mon, Dec 16, 2019 at 9:39 PM Maxime Ripard <mripard@kernel.org> wrote:
>
> On Mon, Dec 16, 2019 at 12:59:21AM +0800, Chen-Yu Tsai wrote:
> > From: Chen-Yu Tsai <wens@csie.org>
> >
> > The CSI0 and CSI1 blocks are the same as found on the A20. However only
> > CSI0 is supported upstream right now.
> >
> > Add a device node for CSI0 using the A20 compatible as a fallback, and
> > the standard pinctrl options. Also add the MBUS interconnect.
> >
> > Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> > ---
> > arch/arm/boot/dts/sun8i-r40.dtsi | 36 ++++++++++++++++++++++++++++++++
> > 1 file changed, 36 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
> > index 82ea0b5b0710..2d1e97cc4155 100644
> > --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> > +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> > @@ -180,6 +180,20 @@ nmi_intc: interrupt-controller@1c00030 {
> > interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> > };
> >
> > + csi0: csi@1c09000 {
> > + compatible = "allwinner,sun8i-r40-csi0",
> > + "allwinner,sun7i-a20-csi0";
> > + reg = <0x01c09000 0x1000>;
> > + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_CSI0>, <&ccu CLK_CSI_SCLK>,
> > + <&ccu CLK_DRAM_CSI0>;
> > + clock-names = "bus", "isp", "ram";
> > + resets = <&ccu RST_BUS_CSI0>;
> > + interconnects = <&mbus 5>;
> > + interconnect-names = "dma-mem";
> > + status = "disabled";
> > + };
> > +
> > mmc0: mmc@1c0f000 {
> > compatible = "allwinner,sun8i-r40-mmc",
> > "allwinner,sun50i-a64-mmc";
> > @@ -355,6 +369,20 @@ clk_out_a_pin: clk-out-a-pin {
> > function = "clk_out_a";
> > };
> >
> > + /omit-if-no-ref/
> > + csi0_8bits_pins: csi0-8bits-pins {
> > + pins = "PE0", "PE2", "PE3", "PE4", "PE5",
> > + "PE6", "PE7", "PE8", "PE9", "PE10",
> > + "PE11";
> > + function = "csi0";
> > + };
> > +
> > + /omit-if-no-ref/
> > + csi0_mclk_pin: csi0-mclk-pin {
> > + pins = "PE1";
> > + function = "csi0";
> > + };
> > +
> > gmac_rgmii_pins: gmac-rgmii-pins {
> > pins = "PA0", "PA1", "PA2", "PA3",
> > "PA4", "PA5", "PA6", "PA7",
> > @@ -624,6 +652,14 @@ gmac_mdio: mdio {
> > };
> > };
> >
> > + mbus: dram-controller@1c62000 {
> > + compatible = "allwinner,sun8i-r40-mbus";
> > + reg = <0x01c62000 0x1000>;
> > + clocks = <&ccu 155>;
>
> We should export the clock too?

I meant to do it separately. Haven't gotten to it though.

ChenYu

\
 
 \ /
  Last update: 2019-12-16 14:43    [W:0.067 / U:7.676 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site