lkml.org 
[lkml]   [2019]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] tty/serial: atmel: fix out of range clock divider handling
From
Date
Hi,

On 13.12.19 at 10:57, Richard Genoud wrote:
> Hi,
>
> Le 11/12/2019 à 17:29, David Engraf a écrit :
>> Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode
>> register was already written thus the clock selection is ignored.
>>
>> Fix by writing the mode register after calculating the baudrate.
>>
>> Signed-off-by: David Engraf <david.engraf@sysgo.com>
>
> It seems that this bug was introduced by:
> commit 5bf5635ac170 ("tty/serial: atmel: add fractional baud rate support")
>
> Could you add the "Fixes:" header ?

Sure.

> Ludovic, could you check if this was your intent at the time ?
>
>> ---
>> drivers/tty/serial/atmel_serial.c | 6 +++---
>> 1 file changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>> index a8dc8af83f39..9983e2fabbac 100644
>> --- a/drivers/tty/serial/atmel_serial.c
>> +++ b/drivers/tty/serial/atmel_serial.c
>> @@ -2270,9 +2270,6 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
>> mode |= ATMEL_US_USMODE_NORMAL;
>> }
>>
> I think it's better to mo move the "Set baud rate" block here (cf bellow)
>
>> - /* set the mode, clock divisor, parity, stop bits and data size */
>> - atmel_uart_writel(port, ATMEL_US_MR, mode);
>> -
>> /*
>> * when switching the mode, set the RTS line state according to the
>> * new mode, otherwise keep the former state
>> @@ -2315,6 +2312,9 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
>> }
>> quot = cd | fp << ATMEL_US_FP_OFFSET;
>>
>> + /* set the mode, clock divisor, parity, stop bits and data size */
>> + atmel_uart_writel(port, ATMEL_US_MR, mode);
>> +
> I think your patch is good, but I'll be happier if instead of moving
> those 2 lines here, the whole "Set the baud rate" block was moved before
> "atmel_uart_writel(port, ATMEL_US_MR, mode);"
>
> That's because at line 2291 the ATMEL_US_CR register is set with
> ATMEL_US_RTSDIS or ATMEL_US_RTSEN.
> And those 2 values have a different effect depending on US_MR.USART_MODE
>
> Quoting from the relase manual:
> RTSEN:
> 1: Drives RTS pin to 1 if US_MR.USART_MODE field = 2, else drives RTS
> pin to 0 if US_MR.USART_MODE field = 0.
>
> RTSDIS:
> 1: Drives RTS pin to 0 if US_MR.USART_MODE field = 2, else drives RTS
> pin to 1 if US_MR.USART_MODE field = 0.
>
> So, I think it's better to set the mode register before setting the
> control register.

I fully agree, the RTS pin configuration depends on USART_MODE. I will
make a new version of the patch.

Thanks
- David


>
>> if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
>> atmel_uart_writel(port, ATMEL_US_BRGR, quot);
>> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
>>
>
> Thanks !
>

\
 
 \ /
  Last update: 2019-12-13 14:49    [W:0.048 / U:22.596 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site