lkml.org 
[lkml]   [2019]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 2/2] PCI: dwc: add support to handle ZRX-DC Compliant PHYs
Date
Many platforms use DesignWare controller but the PHY can be different in
different platforms. If the PHY is compliant is to ZRX-DC specification
it helps in low power consumption during power states.

If current data rate is 8.0 GT/s or higher and PHY is not compliant to
ZRX-DC specification, then after every 100ms link should transition to
recovery state during the low power states.

DesignWare controller provides GEN3_ZRXDC_NONCOMPL field in
GEN3_RELATED_OFF to specify about ZRX-DC compliant PHY.

Platforms with ZRX-DC compliant PHY can set phy_zrxdc_compliant variable
to specify this property to the controller.

Signed-off-by: Anvesh Salveru <anvesh.s@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
---
Changes w.r.t v4:
- None

drivers/pci/controller/dwc/pcie-designware.c | 6 ++++++
drivers/pci/controller/dwc/pcie-designware.h | 4 ++++
2 files changed, 10 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 820488d..36a01b7 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -556,4 +556,10 @@ void dw_pcie_setup(struct dw_pcie *pci)
PCIE_PL_CHK_REG_CHK_REG_START;
dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
}
+
+ if (pci->phy_zrxdc_compliant) {
+ val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
+ val &= ~PORT_LOGIC_GEN3_ZRXDC_NONCOMPL;
+ dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
+ }
}
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 5accdd6..36f7579 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -60,6 +60,9 @@
#define PCIE_MSI_INTR0_MASK 0x82C
#define PCIE_MSI_INTR0_STATUS 0x830

+#define PCIE_PORT_GEN3_RELATED 0x890
+#define PORT_LOGIC_GEN3_ZRXDC_NONCOMPL BIT(0)
+
#define PCIE_ATU_VIEWPORT 0x900
#define PCIE_ATU_REGION_INBOUND BIT(31)
#define PCIE_ATU_REGION_OUTBOUND 0
@@ -249,6 +252,7 @@ struct dw_pcie {
void __iomem *atu_base;
u32 num_viewport;
u8 iatu_unroll_enabled;
+ bool phy_zrxdc_compliant;
struct pcie_port pp;
struct dw_pcie_ep ep;
const struct dw_pcie_ops *ops;
--
2.7.4
\
 
 \ /
  Last update: 2019-12-13 13:48    [W:0.028 / U:4.288 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site