[lkml]   [2019]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v11 net-next 0/2] Use MFD framework for SGI IOC3 drivers
SGI IOC3 ASIC includes support for ethernet, PS2 keyboard/mouse,
NIC (number in a can), GPIO and a byte bus. By attaching a
SuperIO chip to it, it also supports serial lines and a parallel
port. The chip is used on a variety of SGI systems with different
configurations. This patchset moves code out of the network driver,
which doesn't belong there, into its new place a MFD driver and
specific platform drivers for the different subfunctions.

Changes in v11:
- dropped accepted patches out of the series
- moved byte swapping patch first in series
- added ip30 system board support

Changes in v10:
- generation of fake subdevice ID had vendor and device ID swapped

Changes in v9:
- remove generated MFD devices, when driver is removed or in case
of a mfd device setup error
- remove irq domain, if setup of mfd devices failed
- pci_iounmap on exit/error cases
- added irq domain unmap function

Changes in v8:
- Re-worked comments in drivers/mfd/ioc3.c
- Added select CRC16 to ioc3-eth.c
- Patches 1 and 2 are already taken to mips-next, but
for completeness of the series they are still included.
What's missing to get the remaining 3 patches via the MIPS
tree is an ack from a network maintainer

Changes in v7:
- added patch to enable ethernet phy for Origin 200 systems
- depend on 64bit for ioc3 mfd driver

Changes in v6:
- dropped patches accepted for v5.4-rc1
- moved serio patch to ip30 patch series
- adapted nvmem patch

Changes in v5:
- requested by Jakub I've splited ioc3 ethernet driver changes into
more steps to make the transition more visible; on the way there
I've "checkpatched" the driver and reduced code reorderings
- dropped all uint16_t and uint32_t
- added nvmem API extension to the documenation file
- changed to use request_irq/free_irq in serio driver
- removed wrong kfree() in serio error path

Changes in v4:
- added w1 drivers to the series after merge in 5.3 failed because
of no response from maintainer and other parts of this series
won't work without that drivers
- moved ip30 systemboard support to the ip30 series, which will
deal with rtc oddity Lee found
- converted to use devm_platform_ioremap_resource
- use PLATFORM_DEVID_AUTO for serial, ethernet and serio in mfd driver
- fixed reverse christmas order in ioc3-eth.c
- formating issue found by Lee
- re-worked irq request/free in serio driver to avoid crashes during

Changes in v3:
- use 1-wire subsystem for handling proms
- pci-xtalk driver uses prom information to create PCI subsystem
ids for use in MFD driver
- changed MFD driver to only use static declared mfd_cells
- added IP30 system board setup to MFD driver
- mac address is now read from ioc3-eth driver with nvmem framework

Changes in v2:
- fixed issue in ioc3kbd.c reported by Dmitry Torokhov
- merged IP27 RTC removal and 8250 serial driver addition into
main MFD patch to keep patches bisectable

Thomas Bogendoerfer (2):
MIPS: SGI-IP27: fix readb/writeb addressing
mfd: ioc3: Add driver for SGI IOC3 chip

arch/mips/include/asm/mach-ip27/mangle-port.h | 4 +-
arch/mips/include/asm/sn/ioc3.h | 38 +-
arch/mips/sgi-ip27/ip27-timer.c | 20 -
drivers/mfd/Kconfig | 13 +
drivers/mfd/Makefile | 1 +
drivers/mfd/ioc3.c | 700 ++++++++++++++++++
drivers/net/ethernet/sgi/Kconfig | 5 +-
drivers/net/ethernet/sgi/ioc3-eth.c | 544 +++-----------
drivers/rtc/rtc-m48t35.c | 11 +
drivers/tty/serial/8250/8250_ioc3.c | 98 +++
drivers/tty/serial/8250/Kconfig | 11 +
drivers/tty/serial/8250/Makefile | 1 +
12 files changed, 956 insertions(+), 490 deletions(-)
create mode 100644 drivers/mfd/ioc3.c
create mode 100644 drivers/tty/serial/8250/8250_ioc3.c


 \ /
  Last update: 2019-12-13 13:43    [W:0.108 / U:2.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site