lkml.org 
[lkml]   [2019]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] drivers: tty: serial: 8250: fintek: Can enable or disable irq sharing based on isa or pci bus
On Fri, Dec 13, 2019 at 01:17:17PM +0800, chengang@emindsoft.com.cn wrote:
> From: Chen Gang <chengang@emindsoft.com.cn>

Thanks for the patch, my comments below.

> Sorry for this patch being too late, which is for linux-next 20151127 (
> about linux 4.4-rc2). After 4 years, much things have been changed. But
> I think it might be still valuable for some old versions. Welcome anyone
> to refact this patch for their own.

This part should go after '---' line below.

> Fintek serial ports can share irq, but they need be enabled firstly, so
> enable or disable irq sharing based on isa or pci bus. From kconfig, it

irq -> IRQ
isa -> ISA
pci -> PCI
kconfig -> Kconfig

> can be configured.
>
> For integrated 8250 drivers, kernel always calls pnp driver, which will
> not use integrated fintek driver for ever. So let pnp driver try the

fintek -> Fintek or Fintek 8250

> other drivers firstly (e.g. fintek), if fail, try pnp driver its own.

Ditto.

...

> --- a/drivers/tty/serial/8250/8250.h
> +++ b/drivers/tty/serial/8250/8250.h
> @@ -14,6 +14,7 @@
> #include <linux/serial_8250.h>
> #include <linux/serial_reg.h>
> #include <linux/dmaengine.h>

> +#include <linux/pnp.h>

The changes below doesn't require a header.
Pointers are known to the compiler. Names of data structures can be forward
declared. Moreover, these declarations may go inside respective #ifdef.

...

> +#if IS_ENABLED(CONFIG_SERIAL_8250_FINTEK_IRQ_SHARING)
> +
> +static void set_icsr(u16 base_port, u8 index)
> +{
> + uint8_t icsr = 0;
> +
> + outb(LDN, base_port + ADDR_PORT);
> + outb(index, base_port + DATA_PORT);
> + outb(ICSR, base_port + ADDR_PORT);
> + icsr = inb(base_port + DATA_PORT);
> +

> + if (icsr != 0xff) {

if (icsr == 0xff)
return;

?

> + icsr |= IRQ_SHARING_MOD;
> +#if IS_ENABLED(CONFIG_SERIAL_8250_FINTEK_IRQ_SHARING_ISA)
> + icsr |= ISA_IRQ_SHARING;
> +#else
> + icsr |= PCI_IRQ_SHARING;
> +#endif
> + outb(ICSR, base_port + ADDR_PORT);
> + outb(icsr, base_port + DATA_PORT);
> + }
> +}
> +
> +#endif

...

> aux |= inb(addr[i] + DATA_PORT) << 8;
> if (aux != io_address)
> continue;

> -

What the point?

> +#if IS_ENABLED(CONFIG_SERIAL_8250_FINTEK_IRQ_SHARING)
> + set_icsr(addr[i], k);
> +#endif
> fintek_8250_exit_key(addr[i]);
> *key = keys[j];
> *index = k;
> @@ -179,53 +212,6 @@ static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index)
> return -ENODEV;
> }
>
> -static int
> -fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)

Why did you move this function?
It's now not only hard to follow what has been changed, and to review.

> --- a/drivers/tty/serial/8250/8250_pnp.c
> +++ b/drivers/tty/serial/8250/8250_pnp.c
> @@ -438,8 +438,13 @@ static int
> serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
> {
> struct uart_8250_port uart, *port;
> - int ret, line, flags = dev_id->driver_data;
> + int ret, line, flags;
>

> +#if IS_BUILTIN(CONFIG_SERIAL_8250_FINTEK)
> + if (!fintek_8250_probe(dev, dev_id))
> + return 0;
> +#endif
> + flags = dev_id->driver_data;

Oh, I don't like this.
It needs a bit more refactoring done first.

The idea that we are not going to pollute generic driver(s) with quirks anymore
(only when it's really unavoidable).


--
With Best Regards,
Andy Shevchenko

\
 
 \ /
  Last update: 2019-12-13 11:51    [W:0.052 / U:11.932 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site