lkml.org 
[lkml]   [2019]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/3] net: macb: add support for high speed interface
Date
This patch add support for high speed USXGMII PCS and 10G
speed in Cadence ethernet controller driver.

Signed-off-by: Milind Parab <mparab@cadence.com>
---
drivers/net/ethernet/cadence/macb.h | 50 ++++++++
drivers/net/ethernet/cadence/macb_main.c | 138 ++++++++++++++++++++---
2 files changed, 170 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index dbf7070fcdba..b731807d1c49 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -76,10 +76,12 @@
#define MACB_RBQPH 0x04D4

/* GEM register offsets. */
+#define GEM_NCR 0x0000 /* Network Control */
#define GEM_NCFGR 0x0004 /* Network Config */
#define GEM_USRIO 0x000c /* User IO */
#define GEM_DMACFG 0x0010 /* DMA Configuration */
#define GEM_JML 0x0048 /* Jumbo Max Length */
+#define GEM_HS_MAC_CONFIG 0x0050 /* GEM high speed config */
#define GEM_HRB 0x0080 /* Hash Bottom */
#define GEM_HRT 0x0084 /* Hash Top */
#define GEM_SA1B 0x0088 /* Specific1 Bottom */
@@ -164,6 +166,9 @@
#define GEM_DCFG7 0x0298 /* Design Config 7 */
#define GEM_DCFG8 0x029C /* Design Config 8 */
#define GEM_DCFG10 0x02A4 /* Design Config 10 */
+#define GEM_DCFG12 0x02AC /* Design Config 12 */
+#define GEM_USX_CONTROL 0x0A80 /* USXGMII control register */
+#define GEM_USX_STATUS 0x0A88 /* USXGMII status register */

#define GEM_TXBDCTRL 0x04cc /* TX Buffer Descriptor control register */
#define GEM_RXBDCTRL 0x04d0 /* RX Buffer Descriptor control register */
@@ -270,11 +275,19 @@
#define MACB_IRXFCS_OFFSET 19
#define MACB_IRXFCS_SIZE 1

+/* GEM specific NCR bitfields. */
+#define GEM_ENABLE_HS_MAC_OFFSET 31
+#define GEM_ENABLE_HS_MAC_SIZE 1
+
/* GEM specific NCFGR bitfields. */
+#define GEM_FD_OFFSET 1 /* Full duplex */
+#define GEM_FD_SIZE 1
#define GEM_GBE_OFFSET 10 /* Gigabit mode enable */
#define GEM_GBE_SIZE 1
#define GEM_PCSSEL_OFFSET 11
#define GEM_PCSSEL_SIZE 1
+#define GEM_PAE_OFFSET 13 /* Pause enable */
+#define GEM_PAE_SIZE 1
#define GEM_CLK_OFFSET 18 /* MDC clock division */
#define GEM_CLK_SIZE 3
#define GEM_DBW_OFFSET 21 /* Data bus width */
@@ -455,11 +468,17 @@
#define MACB_REV_OFFSET 0
#define MACB_REV_SIZE 16

+/* Bitfield in HS_MAC_CONFIG */
+#define GEM_HS_MAC_SPEED_OFFSET 0
+#define GEM_HS_MAC_SPEED_SIZE 3
+
/* Bitfields in DCFG1. */
#define GEM_IRQCOR_OFFSET 23
#define GEM_IRQCOR_SIZE 1
#define GEM_DBWDEF_OFFSET 25
#define GEM_DBWDEF_SIZE 3
+#define GEM_NO_PCS_OFFSET 0
+#define GEM_NO_PCS_SIZE 1

/* Bitfields in DCFG2. */
#define GEM_RX_PKT_BUFF_OFFSET 20
@@ -494,6 +513,34 @@
#define GEM_RXBD_RDBUFF_OFFSET 8
#define GEM_RXBD_RDBUFF_SIZE 4

+/* Bitfields in DCFG12. */
+#define GEM_HIGH_SPEED_OFFSET 26
+#define GEM_HIGH_SPEED_SIZE 1
+
+/* Bitfields in USX_CONTROL. */
+#define GEM_USX_CTRL_SPEED_OFFSET 14
+#define GEM_USX_CTRL_SPEED_SIZE 3
+#define GEM_SERDES_RATE_OFFSET 12
+#define GEM_SERDES_RATE_SIZE 2
+#define GEM_RX_SCR_BYPASS_OFFSET 9
+#define GEM_RX_SCR_BYPASS_SIZE 1
+#define GEM_TX_SCR_BYPASS_OFFSET 8
+#define GEM_TX_SCR_BYPASS_SIZE 1
+#define GEM_RX_SYNC_RESET_OFFSET 2
+#define GEM_RX_SYNC_RESET_SIZE 1
+#define GEM_TX_EN_OFFSET 1
+#define GEM_TX_EN_SIZE 1
+#define GEM_SIGNAL_OK_OFFSET 0
+#define GEM_SIGNAL_OK_SIZE 1
+
+/* Bitfields in USX_STATUS. */
+#define GEM_USX_TX_FAULT_OFFSET 28
+#define GEM_USX_TX_FAULT_SIZE 1
+#define GEM_USX_RX_FAULT_OFFSET 27
+#define GEM_USX_RX_FAULT_SIZE 1
+#define GEM_USX_BLOCK_LOCK_OFFSET 0
+#define GEM_USX_BLOCK_LOCK_SIZE 1
+
/* Bitfields in TISUBN */
#define GEM_SUBNSINCR_OFFSET 0
#define GEM_SUBNSINCRL_OFFSET 24
@@ -656,6 +703,8 @@
#define MACB_CAPS_GIGABIT_MODE_AVAILABLE 0x20000000
#define MACB_CAPS_SG_DISABLED 0x40000000
#define MACB_CAPS_MACB_IS_GEM 0x80000000
+#define MACB_CAPS_PCS 0x01000000
+#define MACB_CAPS_HIGH_SPEED 0x02000000

/* LSO settings */
#define MACB_LSO_UFO_ENABLE 0x01
@@ -724,6 +773,7 @@
})

#define MACB_READ_NSR(bp) macb_readl(bp, NSR)
+#define GEM_READ_USX_STATUS(bp) gem_readl(bp, USX_STATUS)

/* struct macb_dma_desc - Hardware DMA descriptor
* @addr: DMA address of data buffer
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index ced32d2a85e1..5963a60d54b9 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -81,6 +81,14 @@ struct sifive_fu540_macb_mgmt {
#define MACB_WOL_HAS_MAGIC_PACKET (0x1 << 0)
#define MACB_WOL_ENABLED (0x1 << 1)

+#define HS_MAC_SPEED_100M 0
+#define HS_MAC_SPEED_1000M 1
+#define HS_MAC_SPEED_2500M 2
+#define HS_MAC_SPEED_5000M 3
+#define HS_MAC_SPEED_10000M 4
+
+#define MACB_SERDES_RATE_10G 1
+
/* Graceful stop timeouts in us. We should allow up to
* 1 frame time (10 Mbits/s, full-duplex, ignoring collisions)
*/
@@ -90,6 +98,8 @@ struct sifive_fu540_macb_mgmt {

#define MACB_MDIO_TIMEOUT 1000000 /* in usecs */

+#define MACB_USX_BLOCK_LOCK_TIMEOUT 1000000 /* in usecs */
+
/* DMA buffer descriptor might be different size
* depends on hardware configuration:
*
@@ -506,6 +516,7 @@ static void macb_validate(struct phylink_config *config,
state->interface != PHY_INTERFACE_MODE_RMII &&
state->interface != PHY_INTERFACE_MODE_GMII &&
state->interface != PHY_INTERFACE_MODE_SGMII &&
+ state->interface != PHY_INTERFACE_MODE_USXGMII &&
!phy_interface_mode_is_rgmii(state->interface)) {
bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
return;
@@ -518,6 +529,13 @@ static void macb_validate(struct phylink_config *config,
return;
}

+ if (state->interface == PHY_INTERFACE_MODE_USXGMII &&
+ !(bp->caps & MACB_CAPS_HIGH_SPEED &&
+ bp->caps & MACB_CAPS_PCS)) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ return;
+ }
+
phylink_set_port_modes(mask);
phylink_set(mask, Autoneg);
phylink_set(mask, Asym_Pause);
@@ -527,6 +545,22 @@ static void macb_validate(struct phylink_config *config,
phylink_set(mask, 100baseT_Half);
phylink_set(mask, 100baseT_Full);

+ if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE &&
+ (state->interface == PHY_INTERFACE_MODE_NA ||
+ state->interface == PHY_INTERFACE_MODE_USXGMII)) {
+ phylink_set(mask, 10000baseCR_Full);
+ phylink_set(mask, 10000baseER_Full);
+ phylink_set(mask, 10000baseKR_Full);
+ phylink_set(mask, 10000baseLR_Full);
+ phylink_set(mask, 10000baseLRM_Full);
+ phylink_set(mask, 10000baseSR_Full);
+ phylink_set(mask, 10000baseT_Full);
+ phylink_set(mask, 5000baseT_Full);
+ phylink_set(mask, 2500baseX_Full);
+ phylink_set(mask, 1000baseX_Full);
+ phylink_set(mask, 1000baseT_Full);
+ }
+
if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE &&
(state->interface == PHY_INTERFACE_MODE_NA ||
state->interface == PHY_INTERFACE_MODE_GMII ||
@@ -544,6 +578,60 @@ static void macb_validate(struct phylink_config *config,
__ETHTOOL_LINK_MODE_MASK_NBITS);
}

+static int gem_mac_usx_configure(struct macb *bp,
+ const struct phylink_link_state *state)
+{
+ u32 speed, config, val;
+ int ret;
+
+ val = gem_readl(bp, NCFGR);
+ val = GEM_BIT(PCSSEL) | (~GEM_BIT(SGMIIEN) & val);
+ if (state->pause & MLO_PAUSE_TX)
+ val |= GEM_BIT(PAE);
+ gem_writel(bp, NCFGR, val);
+ gem_writel(bp, NCR, gem_readl(bp, NCR) | GEM_BIT(ENABLE_HS_MAC));
+ gem_writel(bp, NCFGR, gem_readl(bp, NCFGR) | GEM_BIT(FD));
+ config = gem_readl(bp, USX_CONTROL);
+ config = GEM_BFINS(SERDES_RATE, MACB_SERDES_RATE_10G, config);
+ config &= ~GEM_BIT(TX_SCR_BYPASS);
+ config &= ~GEM_BIT(RX_SCR_BYPASS);
+ gem_writel(bp, USX_CONTROL, config | GEM_BIT(TX_EN));
+ config = gem_readl(bp, USX_CONTROL);
+ gem_writel(bp, USX_CONTROL, config | GEM_BIT(SIGNAL_OK));
+ ret = readx_poll_timeout(GEM_READ_USX_STATUS, bp, val,
+ val & GEM_BIT(USX_BLOCK_LOCK),
+ 1, MACB_USX_BLOCK_LOCK_TIMEOUT);
+ if (ret < 0) {
+ netdev_warn(bp->dev, "USXGMII block lock failed");
+ return -ETIMEDOUT;
+ }
+
+ switch (state->speed) {
+ case SPEED_10000:
+ speed = HS_MAC_SPEED_10000M;
+ break;
+ case SPEED_5000:
+ speed = HS_MAC_SPEED_5000M;
+ break;
+ case SPEED_2500:
+ speed = HS_MAC_SPEED_2500M;
+ break;
+ case SPEED_1000:
+ speed = HS_MAC_SPEED_1000M;
+ break;
+ default:
+ case SPEED_100:
+ speed = HS_MAC_SPEED_100M;
+ break;
+ }
+
+ gem_writel(bp, HS_MAC_CONFIG, GEM_BFINS(HS_MAC_SPEED, speed,
+ gem_readl(bp, HS_MAC_CONFIG)));
+ gem_writel(bp, USX_CONTROL, GEM_BFINS(USX_CTRL_SPEED, speed,
+ gem_readl(bp, USX_CONTROL)));
+ return 0;
+}
+
static void macb_mac_pcs_get_state(struct phylink_config *config,
struct phylink_link_state *state)
{
@@ -565,30 +653,39 @@ static void macb_mac_config(struct phylink_config *config, unsigned int mode,

spin_lock_irqsave(&bp->lock, flags);

- old_ctrl = ctrl = macb_or_gem_readl(bp, NCFGR);
+ if (bp->phy_interface == PHY_INTERFACE_MODE_USXGMII) {
+ if (gem_mac_usx_configure(bp, state) < 0) {
+ spin_unlock_irqrestore(&bp->lock, flags);
+ phylink_mac_change(bp->phylink, false);
+ return;
+ }
+ } else {
+ old_ctrl = ctrl = macb_or_gem_readl(bp, NCFGR);

- /* Clear all the bits we might set later */
- ctrl &= ~(GEM_BIT(GBE) | MACB_BIT(SPD) | MACB_BIT(FD) | MACB_BIT(PAE) |
- GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL));
+ /* Clear all the bits we might set later */
+ ctrl &= ~(GEM_BIT(GBE) | MACB_BIT(SPD) |
+ MACB_BIT(FD) | MACB_BIT(PAE) |
+ GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL));

- if (state->speed == SPEED_1000)
- ctrl |= GEM_BIT(GBE);
- else if (state->speed == SPEED_100)
- ctrl |= MACB_BIT(SPD);
+ if (state->speed == SPEED_1000)
+ ctrl |= GEM_BIT(GBE);
+ else if (state->speed == SPEED_100)
+ ctrl |= MACB_BIT(SPD);

- if (state->duplex)
- ctrl |= MACB_BIT(FD);
+ if (state->duplex)
+ ctrl |= MACB_BIT(FD);

- /* We do not support MLO_PAUSE_RX yet */
- if (state->pause & MLO_PAUSE_TX)
- ctrl |= MACB_BIT(PAE);
+ /* We do not support MLO_PAUSE_RX yet */
+ if (state->pause & MLO_PAUSE_TX)
+ ctrl |= MACB_BIT(PAE);

- if (state->interface == PHY_INTERFACE_MODE_SGMII)
- ctrl |= GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL);
+ if (state->interface == PHY_INTERFACE_MODE_SGMII)
+ ctrl |= GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL);

- /* Apply the new configuration, if any */
- if (old_ctrl ^ ctrl)
- macb_or_gem_writel(bp, NCFGR, ctrl);
+ /* Apply the new configuration, if any */
+ if (old_ctrl ^ ctrl)
+ macb_or_gem_writel(bp, NCFGR, ctrl);
+ }

bp->speed = state->speed;

@@ -3407,6 +3504,11 @@ static void macb_configure_caps(struct macb *bp,
dcfg = gem_readl(bp, DCFG1);
if (GEM_BFEXT(IRQCOR, dcfg) == 0)
bp->caps |= MACB_CAPS_ISR_CLEAR_ON_WRITE;
+ if (GEM_BFEXT(NO_PCS, dcfg) == 0)
+ bp->caps |= MACB_CAPS_PCS;
+ dcfg = gem_readl(bp, DCFG12);
+ if (GEM_BFEXT(HIGH_SPEED, dcfg) == 1)
+ bp->caps |= MACB_CAPS_HIGH_SPEED;
dcfg = gem_readl(bp, DCFG2);
if ((dcfg & (GEM_BIT(RX_PKT_BUFF) | GEM_BIT(TX_PKT_BUFF))) == 0)
bp->caps |= MACB_CAPS_FIFO_MODE;
--
2.17.1
\
 
 \ /
  Last update: 2019-12-13 10:44    [W:0.090 / U:5.516 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site