lkml.org 
[lkml]   [2019]   [Dec]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/9] input: elants: support old touch report format
From
Date
12.12.2019 22:45, Michał Mirosław пишет:
> On Thu, Dec 12, 2019 at 03:54:13AM +0300, Dmitry Osipenko wrote:
>> 11.12.2019 19:03, Michał Mirosław пишет:
>>> Support ELAN touchpad sensor with older firmware as found on eg. Asus
>>> Transformer Pads.
> [...]
>>> @@ -814,8 +817,16 @@ static void elants_i2c_mt_event(struct elants_data *ts, u8 *buf)
>>> pos = &buf[FW_POS_XY + i * 3];
>>> x = (((u16)pos[0] & 0xf0) << 4) | pos[1];
>>> y = (((u16)pos[0] & 0x0f) << 8) | pos[2];
>>> - p = buf[FW_POS_PRESSURE + i];
>>> - w = buf[FW_POS_WIDTH + i];
>>> + if (report_len == PACKET_SIZE_OLD) {
>>> + w = buf[FW_POS_WIDTH + i / 2];
>>> + w >>= 4 * (~i & 1); // little-endian-nibbles
>>> + w |= w << 4;
>>> + w |= !w;
>>> + p = w;
>>
>> Did you copy this from the downstream driver as-is? I'm looking at the
>> Nexus 7 driver and it does the following for older format:
>>
>> u8 size_idx[] = { 35, 35, 36, 36, 37, 37, 38, 38, 39, 39 };
>> unsigned int s;
>>
>> if (i & 1)
>> s = buf[size_idx[i]];
>> else
>> s = buf[size_idx[i]] / 16;
>>
>> w = s & 0xf;
>> p = s * 16;
>
> This is the same thing modulo (w), which is scaled here to declared axis
> range (1-255 from 0-15, assuming 0 means "no touch" so it should not occur).
>
> OTOH, I admit, that I don't have any software that can verify those
> settings. It might be that eg. one of MT_PRESSURE or MT_TOUCH_MAJOR axes
> should be dropped in this case, but with no docs I can't be sure what
> the reported values really are.
>
> This is from the original (GPL) code dump labeled 'Asus 10_6_1_27_5':
>
> | touch_size = ((i & 0x01) ? buf[size_index[i]] : (buf[size_index[i]] >> 4)) & 0x0F;
> | if(touch_size == 0) touch_size = 1;
> | if (touch_size <= 7)
> | touch_size = touch_size << 5;
> | else
> | touch_size = 255;
> |
> | input_report_abs(idev, ABS_MT_TOUCH_MAJOR, touch_size);
> | input_report_abs(idev, ABS_MT_PRESSURE, touch_size);

Okay, I also don't know how to test it properly.

If anyone knows, please let us know :)


\
 
 \ /
  Last update: 2019-12-13 01:07    [W:0.036 / U:2.844 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site