lkml.org 
[lkml]   [2019]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/4] ARM: dts: exynos: Correct USB3503 GPIOs polarity
Date
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 2 +-
arch/arm/boot/dts/exynos5250-arndale.dts | 2 +-
arch/arm/boot/dts/exynos5410-odroidxu.dts | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index ea55f377d17c..9c39e82e4ecb 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -267,7 +267,7 @@

intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
initial-mode = <1>;
};

diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index d6c85efdb465..3eddf5dbcf7b 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -154,7 +154,7 @@
compatible = "smsc,usb3503a";

reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
- connect-gpios = <&gpd1 7 GPIO_ACTIVE_LOW>;
+ connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>;
};
};

diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
index e0db251e253f..4f9297ae0763 100644
--- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
@@ -170,7 +170,7 @@

intn-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
connect-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpx1 4 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpx1 4 GPIO_ACTIVE_LOW>;
initial-mode = <1>;

clock-names = "refclk";
--
2.17.1
\
 
 \ /
  Last update: 2019-12-11 15:47    [W:0.041 / U:1.584 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site