lkml.org 
[lkml]   [2019]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH v2 7/9] input: elants: support 0x66 reply opcode for reporting touches
From: Dmitry Osipenko <digetx@gmail.com>

eKTF3624 touchscreen firmware uses two variants of the reply opcodes for
reporting touch events: one is 0x63 (used by older firmware) and other is
0x66 (used by newer firmware). The 0x66 variant is equal to 0x63 of
eKTH3500, while 0x63 needs small adjustment of the touch pressure value.

Nexus 7 tablet device has eKTF3624 touchscreen and it uses 0x66 opcode for
reporting touch events, let's support it now. Other devices, eg. ASUS TF300T,
use 0x63.

Note: CMD_HEADER_REK is used for replying to calibration requests, it has
the same 0x66 opcode number which eKTF3624 uses for reporting touches.
The calibration replies are handled separately from the the rest of the
commands in the driver by entering into ELAN_WAIT_RECALIBRATION state
and thus this change shouldn't change the old behavior.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
---
drivers/input/touchscreen/elants_i2c.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/drivers/input/touchscreen/elants_i2c.c b/drivers/input/touchscreen/elants_i2c.c
index 1c3eb49a22e4..d750eb97c912 100644
--- a/drivers/input/touchscreen/elants_i2c.c
+++ b/drivers/input/touchscreen/elants_i2c.c
@@ -60,6 +60,15 @@
#define QUEUE_HEADER_NORMAL 0X63
#define QUEUE_HEADER_WAIT 0x64

+/*
+ * Depending on firmware version, eKTF3624 touchscreens may utilize one of
+ * these opcodes for the touch events: 0x63 and 0x66. The 0x63 is used by
+ * older firmware version and differs from 0x66 such that touch pressure
+ * value needs to be adjusted. The 0x66 opcode of newer firmware is equal
+ * to 0x63 of eKTH3500.
+ */
+#define QUEUE_HEADER_NORMAL2 0x66
+
/* Command header definition */
#define CMD_HEADER_WRITE 0x54
#define CMD_HEADER_READ 0x53
@@ -990,7 +999,6 @@ static irqreturn_t elants_i2c_irq(int irq, void *_dev)
switch (ts->buf[FW_HDR_TYPE]) {
case CMD_HEADER_HELLO:
case CMD_HEADER_RESP:
- case CMD_HEADER_REK:
break;

case QUEUE_HEADER_WAIT:
@@ -1010,6 +1018,7 @@ static irqreturn_t elants_i2c_irq(int irq, void *_dev)
break;

case QUEUE_HEADER_NORMAL:
+ case QUEUE_HEADER_NORMAL2:
report_count = ts->buf[FW_HDR_COUNT];
if (report_count == 0 || report_count > 3) {
dev_err(&client->dev,
--
2.20.1
\
 
 \ /
  Last update: 2019-12-11 17:04    [W:0.149 / U:3.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site