lkml.org 
[lkml]   [2019]   [Dec]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v4 1/3] dt-bindings: sdhci-of-at91: new compatible string and update properties
On Thu, 28 Nov 2019 at 08:45, Ludovic Desroches
<ludovic.desroches@microchip.com> wrote:
>
> There is a new compatible string for the SAM9X60 sdhci device. It involves
> an update of the properties about the clocks stuff.
>
> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
> Reviewed-by: Rob Herring <robh@kernel.org>

Applied for next, thanks!

Kind regards
Uffe


> ---
>
> Changes:
> - v3: rebase due to conflict with Nicolas' patch
> - v2: remove the extra example and fix node label
>
> .../devicetree/bindings/mmc/sdhci-atmel.txt | 13 ++++++++++---
> 1 file changed, 10 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> index 503c6dbac1b2..69edfd4d3922 100644
> --- a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> +++ b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt
> @@ -5,11 +5,16 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the
> sdhci-of-at91 driver.
>
> Required properties:
> -- compatible: Must be "atmel,sama5d2-sdhci".
> +- compatible: Must be "atmel,sama5d2-sdhci" or "microchip,sam9x60-sdhci".
> - clocks: Phandlers to the clocks.
> -- clock-names: Must be "hclock", "multclk", "baseclk";
> +- clock-names: Must be "hclock", "multclk", "baseclk" for
> + "atmel,sama5d2-sdhci".
> + Must be "hclock", "multclk" for "microchip,sam9x60-sdhci".
>
> Optional properties:
> +- assigned-clocks: The same with "multclk".
> +- assigned-clock-rates The rate of "multclk" in order to not rely on the
> + gck configuration set by previous components.
> - microchip,sdcal-inverted: when present, polarity on the SDCAL SoC pin is
> inverted. The default polarity for this signal is described in the datasheet.
> For instance on SAMA5D2, the pin is usually tied to the GND with a resistor
> @@ -17,10 +22,12 @@ Optional properties:
>
> Example:
>
> -sdmmc0: sdio-host@a0000000 {
> +mmc0: sdio-host@a0000000 {
> compatible = "atmel,sama5d2-sdhci";
> reg = <0xa0000000 0x300>;
> interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
> clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
> clock-names = "hclock", "multclk", "baseclk";
> + assigned-clocks = <&sdmmc0_gclk>;
> + assigned-clock-rates = <480000000>;
> };
> --
> 2.24.0
>

\
 
 \ /
  Last update: 2019-12-10 10:51    [W:0.037 / U:1.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site