lkml.org 
[lkml]   [2019]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH AUTOSEL 4.19 075/191] ARM: dts: stm32: enable display on stm32mp157c-ev1 board
Date
From: Yannick Fertré <yannick.fertre@st.com>

[ Upstream commit 67330599f93672bd351123c729e2591a460fd24c ]

Enable panel raydium RM68200, DSI bridge & display controller.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 73 ++++++++++++++++++++++++---
1 file changed, 67 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 372bc2ea6b921..063ee8ac5dcbd 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -6,6 +6,7 @@
/dts-v1/;

#include "stm32mp157c-ed1.dts"
+#include <dt-bindings/gpio/gpio.h>

/ {
model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
@@ -19,6 +20,58 @@
serial0 = &uart4;
ethernet0 = &ethernet0;
};
+
+ panel_backlight: panel-backlight {
+ compatible = "gpio-backlight";
+ gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
+ default-on;
+ status = "okay";
+ };
+};
+
+&cec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cec_pins_a>;
+ status = "okay";
+};
+
+&dsi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi_in: endpoint {
+ remote-endpoint = <&ltdc_ep0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi_out: endpoint {
+ remote-endpoint = <&dsi_panel_in>;
+ };
+ };
+ };
+
+ panel-dsi@0 {
+ compatible = "raydium,rm68200";
+ reg = <0>;
+ reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
+ backlight = <&panel_backlight>;
+ status = "okay";
+
+ port {
+ dsi_panel_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
};

&ethernet0 {
@@ -40,12 +93,6 @@
};
};

-&cec {
- pinctrl-names = "default";
- pinctrl-0 = <&cec_pins_a>;
- status = "okay";
-};
-
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
@@ -62,6 +109,20 @@
status = "okay";
};

+&ltdc {
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ltdc_ep0_out: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&dsi_in>;
+ };
+ };
+};
+
&m_can1 {
pinctrl-names = "default";
pinctrl-0 = <&m_can1_pins_a>;
--
2.20.1
\
 
 \ /
  Last update: 2019-11-10 03:43    [W:0.523 / U:0.440 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site