lkml.org 
[lkml]   [2019]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/4] MIPS: Ingenic: initial X1000 support.
From
Date
Hi Paul,

On 2019年11月24日 21:09, Paul Cercueil wrote:
> Hi Zhou,
>
>
> Le sam., nov. 23, 2019 at 10:32, Zhou Yanjie <zhouyanjie@zoho.com> a
> écrit :
>> Support the Ingenic X1000 SoC using the code under arch/mips/jz4740.
>> This is left unselectable in Kconfig until a X1000 based board is
>> added in a later commit.
>>
>> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
>> ---
>>
>> Notes:
>> v1->v2:
>> Rebase on top of mips-next, use ingenic-timer driver
>> for system timer and clocksource.
>>
>> arch/mips/boot/dts/ingenic/x1000.dtsi | 183
>> ++++++++++++++++++++++++++++++++++
>> arch/mips/jz4740/Kconfig | 6 ++
>> 2 files changed, 189 insertions(+)
>> create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
>>
>> diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi
>> b/arch/mips/boot/dts/ingenic/x1000.dtsi
>> new file mode 100644
>> index 00000000..02a9b2a
>> --- /dev/null
>> +++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
>> @@ -0,0 +1,183 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +#include <dt-bindings/clock/x1000-cgu.h>
>> +
>> +/ {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + compatible = "ingenic,x1000", "ingenic,x1000e";
>> +
>> + cpuintc: interrupt-controller {
>> + #address-cells = <0>;
>> + #interrupt-cells = <1>;
>> + interrupt-controller;
>> + compatible = "mti,cpu-interrupt-controller";
>> + };
>> +
>> + intc: interrupt-controller@10001000 {
>> + compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
>> + reg = <0x10001000 0x50>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> +
>> + interrupt-parent = <&cpuintc>;
>> + interrupts = <2>;
>> + };
>> +
>> + exclk: ext {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + };
>> +
>> + rtclk: rtc {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <32768>;
>> + };
>> +
>> + cgu: x1000-cgu@10000000 {
>> + compatible = "ingenic,x1000-cgu";
>> + reg = <0x10000000 0x100>;
>> +
>> + #clock-cells = <1>;
>> +
>> + clocks = <&exclk>, <&rtclk>;
>> + clock-names = "ext", "rtc";
>> + };
>> +
>> + apb {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <>;
>
> You can drop the 'apb' node and list the children in the top node
> directly. That's what we do in the devicetree for the other Ingenic SoCs.
>

Sure, I'll drop it in v2.

Thanks and best regards!

> Cheers,
> -Paul
>
>
>> +
>> + tcu: timer@10002000 {
>> + compatible = "ingenic,x1000-tcu",
>> + "ingenic,jz4770-tcu",
>> + "simple-mfd";
>> + reg = <0x10002000 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0x10002000 0x1000>;
>> +
>> + #clock-cells = <1>;
>> +
>> + clocks = <&cgu X1000_CLK_RTCLK
>> + &cgu X1000_CLK_EXCLK
>> + &cgu X1000_CLK_PCLK>;
>> + clock-names = "rtc", "ext", "pclk";
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <27 26 25>;
>> + };
>> +
>> + uart0: serial@10030000 {
>> + compatible = "ingenic,x1000-uart";
>> + reg = <0x10030000 0x100>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <51>;
>> +
>> + clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
>> + clock-names = "baud", "module";
>> +
>> + status = "disabled";
>> + };
>> +
>> + uart1: serial@10031000 {
>> + compatible = "ingenic,x1000-uart";
>> + reg = <0x10031000 0x100>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <50>;
>> +
>> + clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
>> + clock-names = "baud", "module";
>> +
>> + status = "disabled";
>> + };
>> +
>> + uart2: serial@10032000 {
>> + compatible = "ingenic,x1000-uart";
>> + reg = <0x10032000 0x100>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <49>;
>> +
>> + clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
>> + clock-names = "baud", "module";
>> +
>> + status = "disabled";
>> + };
>> +
>> + pinctrl: pin-controller@10010000 {
>> + compatible = "ingenic,x1000-pinctrl";
>> + reg = <0x10010000 0x800>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + gpa: gpio@0 {
>> + compatible = "ingenic,x1000-gpio";
>> + reg = <0>;
>> +
>> + gpio-controller;
>> + gpio-ranges = <&pinctrl 0 0 32>;
>> + #gpio-cells = <2>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <17>;
>> + };
>> +
>> + gpb: gpio@1 {
>> + compatible = "ingenic,x1000-gpio";
>> + reg = <1>;
>> +
>> + gpio-controller;
>> + gpio-ranges = <&pinctrl 0 32 32>;
>> + #gpio-cells = <2>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <16>;
>> + };
>> +
>> + gpc: gpio@2 {
>> + compatible = "ingenic,x1000-gpio";
>> + reg = <2>;
>> +
>> + gpio-controller;
>> + gpio-ranges = <&pinctrl 0 64 32>;
>> + #gpio-cells = <2>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <15>;
>> + };
>> +
>> + gpd: gpio@3 {
>> + compatible = "ingenic,x1000-gpio";
>> + reg = <3>;
>> +
>> + gpio-controller;
>> + gpio-ranges = <&pinctrl 0 96 32>;
>> + #gpio-cells = <2>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <14>;
>> + };
>> + };
>> + };
>> +};
>> diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
>> index 4dd0c44..6b96844 100644
>> --- a/arch/mips/jz4740/Kconfig
>> +++ b/arch/mips/jz4740/Kconfig
>> @@ -33,3 +33,9 @@ config MACH_JZ4780
>> select MIPS_CPU_SCACHE
>> select SYS_HAS_CPU_MIPS32_R2
>> select SYS_SUPPORTS_HIGHMEM
>> +
>> +config MACH_X1000
>> + bool
>> + select MIPS_CPU_SCACHE
>> + select SYS_HAS_CPU_MIPS32_R2
>> + select SYS_SUPPORTS_HIGHMEM
>> --
>> 2.7.4
>>
>>
>
>



\
 
 \ /
  Last update: 2019-11-24 15:43    [W:0.048 / U:3.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site