lkml.org 
[lkml]   [2019]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RFC PATCH 00/21] Implement NTB Controller using multiple PCI
On Thu, Sep 26, 2019 at 7:30 AM 'Kishon Vijay Abraham I' via linux-ntb
<linux-ntb@googlegroups.com> wrote:
>
> This series is sent as RFC since this series is dependent on
> [1] (cannot be merged before that series) and to get early review
> comments.
>
> I'll also split this series into smaller chunk when I post the
> next revision.
>
> This series is about implementing SW defined NTB using
> multiple endpoint instances. This series has been tested using
> 2 endpoint instances in J7 connected to two DRA7 boards.
>
> This was presented in Linux Plumbers Conference. The presentation
> can be found @ [2]
>
> This series:
> *) Add support to define endpoint function using device tree
> *) Add a specification for implementing NTB controller using
> multiple endpoint instances.
> *) Add a NTB endpoint function driver and a NTB host side PCI
> driver that follows the specification.
> *) Add support in PCIe endpoint core to support secondary
> interface.
> *) Add a device tree overlay file to configure J7 as NTB
>
> The test setup is something like below
> +-------------+ +-------------+
> | | | |
> | DRA72 | | DRA76 |
> | | | |
> +------^------+ +------^------+
> | |
> | |
> +---------|-------------------------------------------------|---------+
> | +------v------+ +------v------+ |
> | | | | | |
> | | EP | | EP | |
> | | CONTROLLER1 | | CONTROLLER2 | |
> | | <-----------------------------------> | |
> | | | | | |
> | | | | | |
> | | | J7 | | |
> | | | (Configured using NTB Function) | | |
> | +-------------+ +-------------+ |
> +---------------------------------------------------------------------+
>
> Here DRA72 and DRA76 could be replaced with *any* PCI host.
>
> EP side (J7):
> =============
>
> In the kernel:
> cd /sys/kernel/config/pci_ep/
> echo 1 > controllers/d800000.pcie-ep/start
> echo 1 > controllers/d000000.pcie-ep/start
>
> RC side (DRA7):
> ===============
> echo 0000:01:00.0 > /sys/bus/pci/devices/0000\:01\:00.0/driver/unbind
> echo 0000:01:00.0 > /sys/bus/pci/drivers/ntb_hw_epf/bind
> modprobe ntb_transport
> modprobe ntb_netdev
>
> On each of the hosts Ethernet Interface will be created.
>
> Provide an IP address to each of the hosts:
> HOST1 (dra72):
> ifconfig eth2 192.168.1.2 up
>
> HOST2 (dra76):
> ifconfig eth2 192.168.1.1 up
>
> Once this is done standard network utilities like ping or iperf can be
> used.
>
> root@dra7xx-evm:~# iperf -c 192.168.1.2
> ------------------------------------------------------------
> Client connecting to 192.168.1.2, TCP port 5001
> TCP window size: 2.50 MByte (default)
> ------------------------------------------------------------
> [ 3] local 192.168.1.1 port 60814 connected with 192.168.1.2 port 5001
> [ ID] Interval Transfer Bandwidth
> [ 3] 0.0-10.0 sec 705 MBytes 591 Mbits/sec
>
> [1] -> http://lore.kernel.org/r/20190604131516.13596-1-kishon@ti.com
> [2] -> https://www.linuxplumbersconf.org/event/4/contributions/395/attachments/284/481/Implementing_NTB_Controller_Using_PCIe_Endpoint_-_final.pdf


I had a few nits, but I think this series looks good enough to be sent
out for inclusion.

Thanks,
Jon

> Kishon Vijay Abraham I (21):
> dt-bindings: PCI: Endpoint: Add DT bindings for PCI EPF Bus
> dt-bindings: PCI: Endpoint: Add DT bindings for PCI EPF Device
> dt-bindings: PCI: Endpoint: Add DT bindings for PCI EPF NTB Device
> Documentation: PCI: Add specification for the *PCI NTB* function
> device
> PCI: endpoint: Add API to get reference to EPC from device-tree
> PCI: endpoint: Add API to create EPF device from device tree
> PCI: endpoint: Add "pci-epf-bus" driver
> PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit
> BAR
> PCI: endpoint: Add helper API to get the 'next' unreserved BAR
> PCI: endpoint: Make pci_epf_driver ops optional
> PCI: endpoint: Add helper API to populate header with values from DT
> PCI: endpoint: Add support to associate secondary EPC with EPF
> PCI: endpoint: Add pci_epc_ops to map MSI irq
> PCI: cadence: Implement ->msi_map_irq() ops
> PCI: endpoint: Remove unused pci_epf_match_device()
> PCI: endpoint: Fix missing mutex_unlock in error case
> PCI: endpoint: *_free_bar() to return error codes on failure
> PCI: endpoint: Add EP function driver to provide NTB functionality
> PCI: Add TI J721E device to pci ids
> NTB: Add support for EPF PCI-Express Non-Transparent Bridge
> NTB: tool: Enable the NTB/PCIe link on the local or remote side of
> bridge
>
> Documentation/PCI/endpoint/pci-test-ntb.txt | 315 +++++
> .../bindings/pci/endpoint/pci-epf-bus.txt | 27 +
> .../bindings/pci/endpoint/pci-epf-ntb.txt | 31 +
> .../bindings/pci/endpoint/pci-epf.txt | 28 +
> drivers/ntb/hw/Kconfig | 1 +
> drivers/ntb/hw/Makefile | 1 +
> drivers/ntb/hw/epf/Kconfig | 5 +
> drivers/ntb/hw/epf/Makefile | 1 +
> drivers/ntb/hw/epf/ntb_hw_epf.c | 648 ++++++++++
> drivers/ntb/test/ntb_tool.c | 1 +
> drivers/pci/controller/pcie-cadence-ep.c | 59 +
> drivers/pci/endpoint/Makefile | 3 +-
> drivers/pci/endpoint/functions/Kconfig | 12 +
> drivers/pci/endpoint/functions/Makefile | 1 +
> drivers/pci/endpoint/functions/pci-epf-ntb.c | 1143 +++++++++++++++++
> drivers/pci/endpoint/functions/pci-epf-test.c | 12 +-
> drivers/pci/endpoint/pci-ep-cfs.c | 6 +-
> drivers/pci/endpoint/pci-epc-core.c | 221 +++-
> drivers/pci/endpoint/pci-epf-bus.c | 54 +
> drivers/pci/endpoint/pci-epf-core.c | 133 +-
> include/linux/pci-epc.h | 42 +-
> include/linux/pci-epf.h | 35 +-
> include/linux/pci_ids.h | 1 +
> 23 files changed, 2715 insertions(+), 65 deletions(-)
> create mode 100644 Documentation/PCI/endpoint/pci-test-ntb.txt
> create mode 100644 Documentation/devicetree/bindings/pci/endpoint/pci-epf-bus.txt
> create mode 100644 Documentation/devicetree/bindings/pci/endpoint/pci-epf-ntb.txt
> create mode 100644 Documentation/devicetree/bindings/pci/endpoint/pci-epf.txt
> create mode 100644 drivers/ntb/hw/epf/Kconfig
> create mode 100644 drivers/ntb/hw/epf/Makefile
> create mode 100644 drivers/ntb/hw/epf/ntb_hw_epf.c
> create mode 100644 drivers/pci/endpoint/functions/pci-epf-ntb.c
> create mode 100644 drivers/pci/endpoint/pci-epf-bus.c
>
> --
> 2.17.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-ntb" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-ntb+unsubscribe@googlegroups.com.
> To view this discussion on the web visit https://groups.google.com/d/msgid/linux-ntb/20190926112933.8922-1-kishon%40ti.com.

\
 
 \ /
  Last update: 2019-11-18 00:44    [W:0.166 / U:6.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site