lkml.org 
[lkml]   [2019]   [Oct]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 3/3] pwm: stm32: add power management support
From
Date
On 10/16/19 9:06 AM, Thierry Reding wrote:
> On Fri, Oct 04, 2019 at 02:53:53PM +0200, Fabrice Gasnier wrote:
>> Add suspend/resume PM sleep ops. When going to low power, enforce the PWM
>> channel isn't active. Let the PWM consumers disable it during their own
>> suspend sequence, see [1]. So, perform a check here, and handle the
>> pinctrl states. Also restore the break inputs upon resume, as registers
>> content may be lost when going to low power mode.
>>
>> [1] https://lkml.org/lkml/2019/2/5/770
>>
>> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
>> ---
>> Changes in v2:
>> Follow Uwe suggestions/remarks:
>> - Add a precursor patch to ease reviewing
>> - Use registers read instead of pwm_get_state
>> - Add a comment to mention registers content may be lost in low power mode
>> ---
>> drivers/pwm/pwm-stm32.c | 38 ++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 38 insertions(+)
>
> Applied, thanks. I made two minor changes, though, see below.
>
>>
>> diff --git a/drivers/pwm/pwm-stm32.c b/drivers/pwm/pwm-stm32.c
>> index cf8658c..546b661 100644
>> --- a/drivers/pwm/pwm-stm32.c
>> +++ b/drivers/pwm/pwm-stm32.c
>> @@ -12,6 +12,7 @@
>> #include <linux/mfd/stm32-timers.h>
>> #include <linux/module.h>
>> #include <linux/of.h>
>> +#include <linux/pinctrl/consumer.h>
>> #include <linux/platform_device.h>
>> #include <linux/pwm.h>
>>
>> @@ -655,6 +656,42 @@ static int stm32_pwm_remove(struct platform_device *pdev)
>> return 0;
>> }
>>
>> +static int __maybe_unused stm32_pwm_suspend(struct device *dev)
>> +{
>> + struct stm32_pwm *priv = dev_get_drvdata(dev);
>> + unsigned int ch;
>
> I renamed this to just "i", which is more idiomatic for loop variables.
> The function is small enough not to need to differentiate between loop
> variables.
>
>> + u32 ccer, mask;
>> +
>> + /* Look for active channels */
>> + ccer = active_channels(priv);
>> +
>> + for (ch = 0; ch < priv->chip.npwm; ch++) {
>> + mask = TIM_CCER_CC1E << (ch * 4);
>> + if (ccer & mask) {
>> + dev_err(dev, "The consumer didn't stop us (%s)\n",
>> + priv->chip.pwms[ch].label);
>
> Changed this to:
>
> "PWM %u still in use by consumer %s\n", i, priv->chip.pwms[i].label
>
> I think that might help clarify which PWM is still enabled in case the
> consumers don't set a label.

Hi Thierry,

Many thanks for all the improvements on this series!

Best Regards,
Fabrice

>
> Thierry
>
>> + return -EBUSY;
>> + }
>> + }
>> +
>> + return pinctrl_pm_select_sleep_state(dev);
>> +}
>> +
>> +static int __maybe_unused stm32_pwm_resume(struct device *dev)
>> +{
>> + struct stm32_pwm *priv = dev_get_drvdata(dev);
>> + int ret;
>> +
>> + ret = pinctrl_pm_select_default_state(dev);
>> + if (ret)
>> + return ret;
>> +
>> + /* restore breakinput registers that may have been lost in low power */
>> + return stm32_pwm_apply_breakinputs(priv);
>> +}
>> +
>> +static SIMPLE_DEV_PM_OPS(stm32_pwm_pm_ops, stm32_pwm_suspend, stm32_pwm_resume);
>> +
>> static const struct of_device_id stm32_pwm_of_match[] = {
>> { .compatible = "st,stm32-pwm", },
>> { /* end node */ },
>> @@ -667,6 +704,7 @@ static struct platform_driver stm32_pwm_driver = {
>> .driver = {
>> .name = "stm32-pwm",
>> .of_match_table = stm32_pwm_of_match,
>> + .pm = &stm32_pwm_pm_ops,
>> },
>> };
>> module_platform_driver(stm32_pwm_driver);
>> --
>> 2.7.4
>>

\
 
 \ /
  Last update: 2019-10-16 12:10    [W:0.038 / U:2.688 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site