lkml.org 
[lkml]   [2019]   [Jan]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 0/8] drm/meson: Add support for HDMI2.0 4k60
From
Date
On 31/01/2019 15:13, Andrzej Hajda wrote:
> On 31.01.2019 14:25, Neil Armstrong wrote:
>> Hi Andrzej, Laurent,
>>
>> On 15/01/2019 13:33, Neil Armstrong wrote:
>>> This patchset aims to add support for the following HDMI2.0 4k60 modes:
>>> - 594Mhz TMDS frequency needing TMDS Scramling and 1/40 rate for RGB/YUV4:4:4
>>> - 297MHz TMDS frequency with YUV4:2:0 encoding
>>>
>>> The first mode uses the SCDC helpers introduced by intel to :
>>> - discover where the monitor support SCDC
>>> - setup the SCDC parameters
>>> This is implemented in the dw-hdmi bridge driver by handling scrambling
>>> support during the bridge setup and by exporting an helper for the PHY
>>> setup to setup the SCDC configuration for the 1/40 TMDS rate.
>>> This code will only be active if the encoder support a TMDS rate > 340MHz.
>>>
>>> This patch could eventually break support on different SoC when connected
>>> on a 4k60 monitor with SCDC :
>>> - i.MX correctly discards pixel clocks > 216MHz
>>> - R-CAR discards discards pixel clocks > 297MHz since [1]
>>> - Rockchip discards invalid pixel clocks not in the rockchip_mpll_cfg table
>>> - sun8i correctly discards pixel clocks > 297MHz on a83t
>>> - sun8i discards discards pixel clocks > 594Mhz on h6, which is already broken
>>>
>>> First patch should fix support for Allwinner H6.
>>>
>>> The second mode is implemented by added the missing 4:2:0 bypass handling
>>> in the dw-hdmi bridge driver and adding a "mtmdsclock" separating the
>>> pixel clock from the tmds clock in the mode setup phase.
>>> We also enable support for these modes in the connector only if the platform
>>> glue code explicits the support.
>> Do you think patches 1-4 could be applied ?
>
>
> For me they are OK.
>
> Should I take them via drm-misc?

OK for me !

Neil

>
>
>>
>> Then we could focus on how we manage the bus format between the encoder
>> and the bridge ?
>>
>> Especially patch 5 linked to patch 7.
>>
>> Will one of you be at FOSDEM 2019 ? we could chat about this.
>
>
> Nope.
>
>
> Regards
>
> Andrzej
>
>
>>
>> Following subjects on the table will be :
>> - HDR metadata transmission aligned with the last patchset sent by intel-gfx
>> - Colorspace connector property aligned with the last patchset sent by intel-gfx
>> - HDCP 1.4 and 2.2 handling
>>
>> Neil
>>
>>> Only the meson DRM dw_hdmi glue allows ycbcr420 modes, so no breakage
>>> is expected here.
>>>
>>> The remaining patches adds support for :
>>> - 1/40 TMDS rate aka DIV40 in the dw-hdmi meson PHY setup
>>> - 4:2:0 output and clock setup
>>>
>>> The dw-hdmi support re-uses the support done by Rockchip engineers on the
>>> Linux 4.4 BSP kernel.
>>>
>>> These modes has been validated using a MuxLab HDMI Signal Analyser in
>>> addition to different UHD TVs supporting full 4k60 or the 4:2:0 variant.
>>>
>>> Changes since RFC v2 at [3]:
>>> - Collected tested-by and reviewed-by tags
>>> - Changed if condition in "add HDMI div40 TMDS mode"
>>> - Updated "Add YUV420 output support" with the same if condition
>>>
>>> Changes since RFC v1 at [2]:
>>> - Fix all comments from Laurent :
>>> - Add define for HDMI 1.4 max tmds clock and SCDC supported version
>>> - Call dw_hdmi_set_high_tmds_clock_ratio() in dw_hdmi_phy_enable_powerdown()
>>> to unbreak Allwinner H6
>>> - Pass in_t(u8, bytes, SCDC_MIN_SOURCE_VERSION) as SCDC version
>>> - Finally add comments for SCDC and Scrambling process
>>>
>>> [1] https://patchwork.freedesktop.org/patch/263616/
>>> [2] https://patchwork.freedesktop.org/series/52950/#rev1
>>> [3] https://patchwork.freedesktop.org/series/52950/#rev2
>>>
>>> Neil Armstrong (7):
>>> drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support
>>> drm/meson: add HDMI div40 TMDS mode
>>> drm/meson: add support for HDMI2.0 2160p modes
>>> drm/bridge: dw-hdmi: add support for YUV420 output
>>> drm/bridge: dw-hdmi: allow ycbcr420 modes for >= 0x200a
>>> drm/meson: Add YUV420 output support
>>> drm/meson: Output in YUV444 if sink supports it
>>>
>>> Zheng Yang (1):
>>> drm/bridge: dw-hdmi: support dynamically get input/out color info
>>>
>>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 182 +++++++++++++++++++---
>>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 1 +
>>> drivers/gpu/drm/meson/meson_dw_hdmi.c | 128 ++++++++++++---
>>> drivers/gpu/drm/meson/meson_vclk.c | 93 ++++++++---
>>> drivers/gpu/drm/meson/meson_vclk.h | 7 +-
>>> drivers/gpu/drm/meson/meson_venc.c | 8 +-
>>> drivers/gpu/drm/meson/meson_venc.h | 11 ++
>>> drivers/gpu/drm/meson/meson_venc_cvbs.c | 3 +-
>>> include/drm/bridge/dw_hdmi.h | 7 +
>>> 9 files changed, 374 insertions(+), 66 deletions(-)
>>>
>>
>>
>
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>

\
 
 \ /
  Last update: 2019-01-31 16:50    [W:0.164 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site