lkml.org 
[lkml]   [2019]   [Jan]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] ARM: socfpga: fix base address of SDR controller
From
Date


On 1/30/19 12:00 AM, Simon Goldschmidt wrote:
> + Marek (as I really want to keep the dts in Linux and U-Boot in sync)
> On Wed, Jan 30, 2019 at 1:16 AM Dinh Nguyen <dinguyen@kernel.org> wrote:
>>
>>
>>
>> On 1/29/19 2:08 PM, Simon Goldschmidt wrote:
>>> From: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
>>>
>>> The documentation for socfpga gen5 says the base address of the sdram
>>> controller is 0xffc20000, while the current devicetree says it is at
>>> 0xffc25000.
>>>
>>> While this is not a problem for Linux, as it only accesses the registers
>>> above 0xffc25000, it *is* a problem for U-Boot because the lower registers
>>> are used during DDR calibration (up to now, the U-Boot driver does not use
>>> the dts address, but that should change).
>>>
>>> To keep Linux and U-Boot devicetrees in sync, this patch changes the base
>>> address to 0xffc20000 and adapts the 2 files where it is currently used.
>>>
>>> This patch changes the dts and 2 drivers with one commit to prevent
>>> breaking the code if dts change and driver change would be split.
>>>
>>> Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
>>> ---
>>>
>>> arch/arm/boot/dts/socfpga.dtsi | 4 ++--
>>> arch/arm/mach-socfpga/self-refresh.S | 4 ++--
>>> drivers/fpga/altera-fpga2sdram.c | 2 +-
>>> 3 files changed, 5 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
>>> index f365003f0..8f6c1a5d6 100644
>>> --- a/arch/arm/boot/dts/socfpga.dtsi
>>> +++ b/arch/arm/boot/dts/socfpga.dtsi
>>> @@ -788,9 +788,9 @@
>>> reg = <0xfffec000 0x100>;
>>> };
>>>
>>> - sdr: sdr@ffc25000 {
>>> + sdr: sdr@ffc20000 {
>>> compatible = "altr,sdr-ctl", "syscon";
>>> - reg = <0xffc25000 0x1000>;
>>> + reg = <0xffc20000 0x6000>;
>>
>> I don't see the U-Boot device tree having this change. Yes, the
>> documentation does state that the SDR address starts at 0xffc20000, but
>> all of the pertinent registers start at 0x5000 offset. Thus, the
>> starting address should be 0xffc25000.[1]
>
> You don't see it in U-Boot as I'm working on a patch for that.
> As I wrote in the commit message, U-Boot currently does not use the
> devicetree for the SDR driver, but I want to convert it to do that.

That's great! Can you elaborate on what is the impetus for converting
the SDR driver to use the dts?

Dinh

\
 
 \ /
  Last update: 2019-01-30 16:51    [W:0.092 / U:5.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site