lkml.org 
[lkml]   [2019]   [Jan]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 4/7] mmc: sdhci: Add quirk for disabling DTO during erase command
From
Date
Hi Adrian,

On 24/01/19 5:38 PM, Adrian Hunter wrote:
> On 11/01/19 1:08 PM, Faiz Abbas wrote:
>> Some controllers might prematurely issue a data timeout during an erase
>> command. Add a quirk to disable the interrupt when an erase command is
>> issued.
>
> I might have already asked this, but would it be possible to use the
> existing SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk?

This looks promising. Let me look into this. In any case, I should
probably move this to something like sdhci_set_timeout and use
sdhci_set_data_timeout_irq().

I was following 93caf8e69eac ("omap_hsmmc: add erase capability") for
adding this.

Thanks,
Faiz

>
>>
>> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
>> ---
>> drivers/mmc/host/sdhci.c | 8 ++++++++
>> drivers/mmc/host/sdhci.h | 2 ++
>> 2 files changed, 10 insertions(+)
>>
>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>> index 4a9044c06e21..cfd716aee552 100644
>> --- a/drivers/mmc/host/sdhci.c
>> +++ b/drivers/mmc/host/sdhci.c
>> @@ -1560,6 +1560,14 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
>> /* Initially, a command has no error */
>> cmd->error = 0;
>>
>> + if (cmd->opcode == MMC_ERASE &&
>> + (host->quirks2 & SDHCI_QUIRK2_DISABLE_DTO_FOR_ERASE)) {
>> + mask = sdhci_readl(host, SDHCI_INT_ENABLE);
>> + mask &= ~SDHCI_INT_DATA_TIMEOUT;
>> + sdhci_writel(host, mask, SDHCI_INT_ENABLE);
>> + sdhci_writel(host, mask, SDHCI_SIGNAL_ENABLE);
>> + }
>> +
>> if ((host->quirks2 & SDHCI_QUIRK2_STOP_WITH_TC) &&
>> cmd->opcode == MMC_STOP_TRANSMISSION)
>> cmd->flags |= MMC_RSP_BUSY;
>> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
>> index 7a52823ebef4..d0c6d4fe5371 100644
>> --- a/drivers/mmc/host/sdhci.h
>> +++ b/drivers/mmc/host/sdhci.h
>> @@ -479,6 +479,8 @@ struct sdhci_host {
>> * block count.
>> */
>> #define SDHCI_QUIRK2_USE_32BIT_BLK_CNT (1<<18)
>> +/* Controller needs to disable DTO for erase command */
>> +#define SDHCI_QUIRK2_DISABLE_DTO_FOR_ERASE (1<<19)
>>
>> int irq; /* Device IRQ */
>> void __iomem *ioaddr; /* Mapped address */
>>
>

\
 
 \ /
  Last update: 2019-01-28 12:17    [W:0.112 / U:2.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site