lkml.org 
[lkml]   [2019]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
From
Date

On 21-Jan-19 3:07 PM, Tudor.Ambarus@microchip.com wrote:
> Hi, Purna,
>
> On 12/14/2018 04:15 AM, Purna Chandra Mandal wrote:
>> cadence-quadspi controller allows upto eight bytes of data to be transferred
>> in software Triggered Instruction generator (STIG) mode of operation. Lower
>> 4 bytes are written through writedatalower and upper 4 bytes by
>> writedataupper register.
>
> Is this supported by all versions of the IP?
>
Yes, it is supported on all versions of IP.
>>
>> This patch allows all the 8 bytes to be written.
>>
>> Signed-off-by: Purna Chandra Mandal <purna.chandra.mandal@intel.com>
>> ---
>>
>> drivers/mtd/spi-nor/cadence-quadspi.c | 9 +++++++--
>> 1 file changed, 7 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c
>> index 04cedd3a2bf6..990934387fea 100644
>> --- a/drivers/mtd/spi-nor/cadence-quadspi.c
>> +++ b/drivers/mtd/spi-nor/cadence-quadspi.c
>> @@ -420,7 +420,7 @@ static int cqspi_command_write(struct spi_nor *nor, const u8 opcode,
>> unsigned int data;
>
> I know that this is not your change, but data should be u32 and not unsigned
> int. reg too ... probably one should submit a patch to change this, I see that
> the same error is done in cqspi_command_read().
ack. will be done in separate patch.
>
>> int ret;
>>
>> - if (n_tx > 4 || (n_tx && !txbuf)) {
>> + if (n_tx > CQSPI_STIG_DATA_LEN_MAX || (n_tx && !txbuf)) {
>> dev_err(nor->dev,
>> "Invalid input argument, cmdlen %d txbuf 0x%p\n",
>> n_tx, txbuf);
>> @@ -435,8 +435,13 @@ static int cqspi_command_write(struct spi_nor *nor, const u8 opcode,
>> data = 0;> memcpy(&data, txbuf, n_tx);
>
> You should limit what is copied in data, similar to what is done in
> cqspi_command_read():
>
> write_len = (n_tx > 4) ? 4 : n_tx;
> memcpy(&data, txbuf, write_len);
> txbuf += write_len;
ack.
>
>
>
>> writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER);
>> - }
>>
>> + if (n_tx > 4) {
>> + data = 0;
> and then:
> write_len = n_tx - 4;
> memcpy(&data, txbuf, write_len);
>
ack.
> Cheers,
> ta
>
>> + memcpy(&data, txbuf + 4, n_tx - 4);
>> + writel(data, reg_base + CQSPI_REG_CMDWRITEDATAUPPER);
>> + }
>> + }
>> ret = cqspi_exec_flash_cmd(cqspi, reg);
>> return ret;
>> }
>>

\
 
 \ /
  Last update: 2019-01-28 05:57    [W:0.473 / U:11.708 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site